BalisongWiki - User contributions [en]

Pivot System

2026-07-04T16:47:18Z

DexyStorm: add info on how to convert to bushings

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

===Convert Washer To Bushing===

In order to convert a washer balisong to a bushing balisong, you will need to enlargen the pivot holes so that bushings fit into them.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Pivot_System#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Loose Tolerances With Undersized Bushing====

If you have confirmed that your bushing is undersized but you still have a lot of play when you crank the screws, then your sex bolt is probably too long.
The sex bolt should not extend past the second handle halve, but rather sit recessed within it.<br>
To shorten the sex bolt, just use the same technique as described in the [[#Lapping Methods]] chapters.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washer=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

The only difference between a [[Pivot_System#Bushing|Traditional Bushing system]] and the Floating Washer system, is that in the Floating Washer system, the washers go around the bushing, "floating" in-between the handle and blade.

===Tuning Floating Bushings===

===Converting Floating Washer To Bushing===

Most Floating Washer balisongs can be converted to a traditional bushing pivot system by just switching to washers that sit on top of the bushing.

==Bearing==

Tuning a Bearing balisong has the exact same procedure as tuning a washer balisong.

==Converting Bearing to Bushing==

Converting a Bearing balisong to a bushing balisong has the exact same procedure as converting a washer balisong to a bushing balisong with the addition that because bearings tend to be thicker, you might need to use thicker bushings that fill in the space that was ocupied by the bearings.

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[

Pivot System

2026-07-04T16:23:48Z

DexyStorm: add info on what's different between traditional bushing system and floating washer system

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Pivot_System#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Loose Tolerances With Undersized Bushing====

If you have confirmed that your bushing is undersized but you still have a lot of play when you crank the screws, then your sex bolt is probably too long.
The sex bolt should not extend past the second handle halve, but rather sit recessed within it.<br>
To shorten the sex bolt, just use the same technique as described in the [[#Lapping Methods]] chapters.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washer=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

The only difference between a [[Pivot_System#Bushing|Traditional Bushing system]] and the Floating Washer system, is that in the Floating Washer system, the washers go around the bushing, "floating" in-between the handle and blade.

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Main Page

2026-07-04T04:05:29Z

DexyStorm: remove URL change announcement

__NOTOC__

== Welcome to the Balisong Wiki ==

The Balisong Wiki is supposed to be a one-stop hub for everything balisong related.


= Using The Balisong Wiki =

<div style="display: flex; flex-wrap: wrap; gap: 2em; align-items: flex-start; margin-top: 1em;">


<div style="flex: 1; min-width: 300px;">

===Reading===

<p>If are not interested in contributing and just want quick access to information, use the search bar at the top right of the screen. Alternatively, here are some articles that might interest you.</p>

<p>[[Balisong_List|Balisong List]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A comprehensive list of balisongs and their components.</div>

<p>[[Community]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A page dedicated to listing places where the community is most active.</div>

<p>[[Meta]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Some trivia and general information about the Balisong Wiki itself.</div>

<p>[[Pivot_System|Pivot System]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A list on pivot systems and written tutorials how to tune them.</div>

<p>[[Frequently_Asked_Questions|Frequently Asked Questions]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Some frequently asked questions and the answers to them.</div>

</div>


<div style="flex: 1; min-width: 300px;">

===Contributing===

There are two main ways in which you can contribute to the Balisong Wiki.

<p>[[Edit Guide]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A guide on how to edit the Balisong Wiki.</div>

<p>[https://ko-fi.com/dexystorm/donate Donations]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Donations will mainly go towards paying for a better server, more storage and renting out Domain names.</div>

</div>

</div>


=Contact=

There are multiple ways to contact the admin team and/or the owner.

<div style="display: flex; flex-wrap: wrap; gap: 2em; align-items: flex-start; margin-top: 1em;">


<div style="flex: 1; min-width: 300px;">

<p>[https://discord.gg/Jyggahn5B7 Discord Server]</p>
<div style="margin-left: 1.5em; font-size: 90%;">The best way to get in touch is through the Balisong Wiki Discord server.</div>

<p>[https://discord.com/users/336184339043713034 Discord Direct Message]</p>
<div style="margin-left: 1.5em; font-size: 90%;">I will not accept any friend requests, but I will respond to all direct message requests. In case the direct link above does not work, my username on Discord is "DexyStorm".</div>

<p>[mailto:dexystormlp@gmail.com E-Mail]</p>
<div style="margin-left: 1.5em; font-size: 90%;">If you do not have a Discord account, you can also contact me via E-Mail: dexystormlp@gmail.com</div>

</div>


<div style="flex: 1; min-width: 300px;">

<p>[https://www.instagram.com/dexystorm/ Instagram account]</p>
<div style="margin-left: 1.5em; font-size: 90%;">If you prefer to not use E-Mails, i also have an Instagram account.</div>

<p>[https://www.reddit.com/user/Dexy_Storm/ Reddit]</p>
<div style="margin-left: 1.5em; font-size: 90%;">You can contact me through direct messages on Reddit.</div>

<p>[[User_talk:DexyStorm|The Owner's Talk Page]] </p>
<div style="margin-left: 1.5em; font-size: 90%;">Please keep in mind that everything that you post on my Talk page will be publicly visible.
</div>

</div>
</div>

Sandbox

2026-06-28T22:31:15Z

DexyStorm:

This is the sandbox. On this page you can freely make changes to familiarize yourself with how to edit the BalisongWiki.

==a==

===ab===

==b==

==c==

test

testtest

abcdefghijklmnop

Washer

2026-06-16T09:52:32Z

DexyStorm: add second "

[[File:Balisong cross section washer.png|700px|thumb|right|Bushing Balisong With Washer Cross section]]

==Material==

Washers used in balisongs are typically made from one of three metals: [https://en.wikipedia.org/wiki/Phosphor_bronze phosphor bronze], [https://en.wikipedia.org/wiki/Brass brass] or [https://en.wikipedia.org/wiki/Stainless_steel stainless steel]. They sit between the handles and the blade in order to reduce friction and minimize the damage to the blade which makes them expendable wear items.

===Phosphor Bronze===

[https://en.wikipedia.org/wiki/Phosphor_bronze Phosphor bronze] (often shortened to "PB") washers are the industry standard for balisongs these days because they offer low friction, decent wear and corrosion resistance and are not going to abraide the blade.

===Stainless Steel===

Stainless steel washers are much harder than phosphor bronze or brass. This property has upsides and downsides: It is good because it means that the stainless steel washers won't deform and will only need replacting very rarely, or not at all. The downside is that that washers are supposed to be "sacrificial" to protect the blade as explained in in the [[#Material]] chapter. However, due to it's much higher hardness the washer is no longer "sacrificial" becuase instead of the washer being worn down, now the washer AND the blade are being worn down.

===Brass===

Some cheaper balisongs, especially [[Clone|Clones]] use brass washers. Brass is a lot softer than phosphor bronze and stainless steel, meaning it will bend around the [[Pivot_System|Bushing]] a lot more, allowing for a balisong which has a lose tune, to feel tighter. It however lacks the low friction and wear resistance which PB offers.

==Size==

The two most important measurements for washers are the height(/thickness) and outer diameter. The inner diameter usually isnt as important, as long as it's close enough to being slightly larger than the OD of the shaft of the sexbolt.

===Thickness===

Most balisongs use washers that are 0.5mm high. There are however exceptions to this, like the [[Bladerunners_Systems_Replicant_V3|Replicant]], who require thinner washers of 0.4mm, or the [[LDY_Sirius_V4|Sirius V4]] which requires 1mm washers.

===Outer Diameter===

When you swap out your current washers for new ones, make sure that the new washers have the same outer diameter as your old washers. That is because the outer diameter of washers can play a crucial role in a balisongs tune. To learn more about this, read this chapter: [[Pivot_System|Pivot_System#Different Outer Diameter Of Washer]].

Balisong List

2026-06-15T13:12:18Z

DexyStorm: add Di Studio Litetech

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[935 Design]]
|[[935 Design MAXIS|MAXIS]]
|S45
|[[Construction#Sandwich|Sandwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| 301SS + Micarta
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V + Nitride Coat
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti / 6AL-4V + G10/CF/Blue Twill
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| G10/CF + 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Ultem Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 4.016x4.80x7.001
|
| 6.320x2.00x3.413x5.50x7.725
| 6.314x2.03x4.805x7.61x9.464
| 0.494x5.20x10.001
|-
| rowspan="24" | [[LDY]]
| [[LDY Aquatic|Aquatic]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TC21 Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Corvus|Corvus]]
| 440C; 3CR13
| [[Construction#Channel|Channel]]
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus EVO|Cygnus EVO]]
| 440C
|
| 6AL-4V Ti + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank-P|Frank-P]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="21" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al / Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10; 440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Vulp Teflon|Vulp Teflon]]
| 420
| [[Construction#Channel|Channel]]
| 7075 AL + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="34" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-C|Squiddy-C]]
| Polycarbonate
| [[Construction#Channel|Channel]]
| Polycarbonate
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-G|Squiddy-G]]
| Gray CPVC
| [[Construction#Channel|Channel]]
| Gray CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami V1|Tsunami V1]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V2|Tsunami V2]]
|5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V3|Tsunami V3]]
|Damascus;5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
| rowspan="13" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
| 6.341x2.03x3.382x6.07x8.211
| 6.338x1.98x4.758x8.00x10.090
| 0.702x4.90x10.018
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
| 7.799x1.83x3.353x4.90x6.577
| 7.780x1.84x4.766x8.86x10.796
| 0.404x4.89x9.44
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x4.80x7.050
|
| 6.40x1.84x3.460x5.62x7.475
| 6.41x1.90x4.775x9.54x11.530
| 0.395x4.90x9.44
|-
| [[Baliplus Squid Industries Tsunami V1|Tsunami V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V2|Tsunami V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V3|Tsunami V3]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V4|Tsunami V4]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|?x?x6.275
|
|
|
|0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
|[[Di Studio]]
|[[JK Di Studio Litetech|Litetech]]
|
|[[Construction#Sandwich|Sandwich]]
|TI (+ G10)
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|3.510x?x6.411
|
|
|
|0.803x?x?
|-
| [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
|
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
|
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-06-07T17:03:03Z

DexyStorm: add maxis linking

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[935 Design]]
|[[935 Design MAXIS|MAXIS]]
|S45
|[[Construction#Sandwich|Sandwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Ultem Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 4.016x4.80x7.001
|
| 6.320x2.00x3.413x5.50x7.725
| 6.314x2.03x4.805x7.61x9.464
| 0.494x5.20x10.001
|-
| rowspan="24" | [[LDY]]
| [[LDY Aquatic|Aquatic]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TC21 Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Corvus|Corvus]]
| 440C; 3CR13
| [[Construction#Channel|Channel]]
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus EVO|Cygnus EVO]]
| 440C
|
| 6AL-4V Ti + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank-P|Frank-P]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="21" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10; 440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Vulp Teflon|Vulp Teflon]]
| 420
| [[Construction#Channel|Channel]]
| 7075 AL + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="34" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-C|Squiddy-C]]
| Polycarbonate
| [[Construction#Channel|Channel]]
| Polycarbonate
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-G|Squiddy-G]]
| Gray CPVC
| [[Construction#Channel|Channel]]
| Gray CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami V1|Tsunami V1]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V2|Tsunami V2]]
|5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V3|Tsunami V3]]
|Damascus;5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
| rowspan="13" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
| 6.341x2.03x3.382x6.07x8.211
| 6.338x1.98x4.758x8.00x10.090
| 0.702x4.90x10.018
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
| 7.799x1.83x3.353x4.90x6.577
| 7.780x1.84x4.766x8.86x10.796
| 0.404x4.89x9.44
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x4.80x7.050
|
| 6.40x1.84x3.460x5.62x7.475
| 6.41x1.90x4.775x9.54x11.530
| 0.395x4.90x9.44
|-
| [[Baliplus Squid Industries Tsunami V1|Tsunami V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V2|Tsunami V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V3|Tsunami V3]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V4|Tsunami V4]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|?x?x6.275
|
|
|
|0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-06-07T17:02:12Z

DexyStorm: add 935 Design

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[935 Design]]
|MAXIS
|S45
|[[Construction#Sandwich|Sandwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Ultem Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 4.016x4.80x7.001
|
| 6.320x2.00x3.413x5.50x7.725
| 6.314x2.03x4.805x7.61x9.464
| 0.494x5.20x10.001
|-
| rowspan="24" | [[LDY]]
| [[LDY Aquatic|Aquatic]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TC21 Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Corvus|Corvus]]
| 440C; 3CR13
| [[Construction#Channel|Channel]]
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus EVO|Cygnus EVO]]
| 440C
|
| 6AL-4V Ti + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank-P|Frank-P]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="21" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10; 440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Vulp Teflon|Vulp Teflon]]
| 420
| [[Construction#Channel|Channel]]
| 7075 AL + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="34" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-C|Squiddy-C]]
| Polycarbonate
| [[Construction#Channel|Channel]]
| Polycarbonate
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-G|Squiddy-G]]
| Gray CPVC
| [[Construction#Channel|Channel]]
| Gray CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami V1|Tsunami V1]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V2|Tsunami V2]]
|5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V3|Tsunami V3]]
|Damascus;5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
| rowspan="13" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
| 6.341x2.03x3.382x6.07x8.211
| 6.338x1.98x4.758x8.00x10.090
| 0.702x4.90x10.018
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
| 7.799x1.83x3.353x4.90x6.577
| 7.780x1.84x4.766x8.86x10.796
| 0.404x4.89x9.44
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x4.80x7.050
|
| 6.40x1.84x3.460x5.62x7.475
| 6.41x1.90x4.775x9.54x11.530
| 0.395x4.90x9.44
|-
| [[Baliplus Squid Industries Tsunami V1|Tsunami V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V2|Tsunami V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V3|Tsunami V3]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V4|Tsunami V4]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|?x?x6.275
|
|
|
|0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-06-07T16:50:33Z

DexyStorm: add Baliplus tsunami versions

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Ultem Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 4.016x4.80x7.001
|
| 6.320x2.00x3.413x5.50x7.725
| 6.314x2.03x4.805x7.61x9.464
| 0.494x5.20x10.001
|-
| rowspan="24" | [[LDY]]
| [[LDY Aquatic|Aquatic]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TC21 Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Corvus|Corvus]]
| 440C; 3CR13
| [[Construction#Channel|Channel]]
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus EVO|Cygnus EVO]]
| 440C
|
| 6AL-4V Ti + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank-P|Frank-P]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="21" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10; 440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Vulp Teflon|Vulp Teflon]]
| 420
| [[Construction#Channel|Channel]]
| 7075 AL + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="34" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-C|Squiddy-C]]
| Polycarbonate
| [[Construction#Channel|Channel]]
| Polycarbonate
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-G|Squiddy-G]]
| Gray CPVC
| [[Construction#Channel|Channel]]
| Gray CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami V1|Tsunami V1]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V2|Tsunami V2]]
|5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V3|Tsunami V3]]
|Damascus;5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
| rowspan="13" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
| 6.341x2.03x3.382x6.07x8.211
| 6.338x1.98x4.758x8.00x10.090
| 0.702x4.90x10.018
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
| 7.799x1.83x3.353x4.90x6.577
| 7.780x1.84x4.766x8.86x10.796
| 0.404x4.89x9.44
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x4.80x7.050
|
| 6.40x1.84x3.460x5.62x7.475
| 6.41x1.90x4.775x9.54x11.530
| 0.395x4.90x9.44
|-
| [[Baliplus Squid Industries Tsunami V1|Tsunami V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V2|Tsunami V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V3|Tsunami V3]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Baliplus Squid Industries Tsunami V4|Tsunami V4]]
|VG10
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|?x?x6.275
|
|
|
|0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-06-07T16:45:09Z

DexyStorm: add different armed shark tsunami versions

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Ultem Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 4.016x4.80x7.001
|
| 6.320x2.00x3.413x5.50x7.725
| 6.314x2.03x4.805x7.61x9.464
| 0.494x5.20x10.001
|-
| rowspan="24" | [[LDY]]
| [[LDY Aquatic|Aquatic]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TC21 Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Corvus|Corvus]]
| 440C; 3CR13
| [[Construction#Channel|Channel]]
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus EVO|Cygnus EVO]]
| 440C
|
| 6AL-4V Ti + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank-P|Frank-P]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="21" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
| 420C
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10; 440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Vulp Teflon|Vulp Teflon]]
| 420
| [[Construction#Channel|Channel]]
| 7075 AL + Teflon
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="34" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
| 304
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-C|Squiddy-C]]
| Polycarbonate
| [[Construction#Channel|Channel]]
| Polycarbonate
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-G|Squiddy-G]]
| Gray CPVC
| [[Construction#Channel|Channel]]
| Gray CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
| 304
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami V1|Tsunami V1]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V2|Tsunami V2]]
|5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
|[[Armed Shark Squid Industries Tsunami V3|Tsunami V3]]
|Damascus;5Cr15
|[[Construction#Chanwich|Chanwich]]
|TI
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|2.849x4.8x6.987
|
|6.76x1.90x3.39x5.52x7.323
|6.66x1.90x4.774x7.56x9.392
|0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
| 6.341x2.03x3.382x6.07x8.211
| 6.338x1.98x4.758x8.00x10.090
| 0.702x4.90x10.018
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
| 7.799x1.83x3.353x4.90x6.577
| 7.780x1.84x4.766x8.86x10.796
| 0.404x4.89x9.44
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x4.80x7.050
|
| 6.40x1.84x3.460x5.62x7.475
| 6.41x1.90x4.775x9.54x11.530
| 0.395x4.90x9.44
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Bladerunners Systems Replicant V3

2026-06-01T19:54:29Z

DexyStorm:

==Overview==

The Replicant is a balisong made by [[Bladerunners_Systems|Bladerunners Systems]].

==Description==

====Handle====

=====Handle Design=====

The Replicant is a [[Construction#Sandwich]] balisong with a with [[Pin_System#Screw_Zen|Pin_System#Screw Zen]] pins.

=====Handle Dimension=====

The handles are [[Taper|tapered]] and are ? wide near the pivots and ? wide near the end.

=====Handle Weight=====

====Blade====

Replicants come with two blade options: the alt blade, which is a spearpoint and a tanto blade.

=====Tanto=====

======Tanto Blade Design======

======Tanto Blade Weight======

======Tanto Blade Dimensions======

=====Alt=====

======Alt Blade Design======

======Alt Blade Weight======

The alt blade weighs 44g.

======Alt Blade Dimensions======

The blade is 3.175mm thick near the washer area.

=====Blade Steel=====

Both the tanto and the spearpoint blade are made out of [https://en.wikipedia.org/wiki/154CM 154CM].

===Balance===

==Hardware==

Body/Zen Pin Screw:<br>
Select .188 [https://thetruelink.com/products/button-head-torx-screw-2-56-pitch?_pos=1&_sid=a2642146a&_ss=r https://thetruelink.com/products/button-head-torx-screw-2-56-pitch?_pos=1&_sid=a2642146a&_ss=r]

Body Sexbolt:<br>
Select .40 [https://thetruelink.com/products/1-8-x-2-56-tpi-stainless-sex-bolt-gray-finish-416-stainless?_pos=1&_sid=72c8d9d25&_ss=r https://thetruelink.com/products/1-8-x-2-56-tpi-stainless-sex-bolt-gray-finish-416-stainless?_pos=1&_sid=72c8d9d25&_ss=r]

Bushing:<br>
Select .126 [https://thetruelink.com/products/250-od-x-188id-x-126-oal-bushing?_pos=2&_sid=b440d34da&_ss=r&variant=41075337298103 https://thetruelink.com/products/250-od-x-188id-x-126-oal-bushing?_pos=2&_sid=b440d34da&_ss=r&variant=41075337298103]

Pivot Screw:<br>
Select .250 [https://thetruelink.com/products/button-head-torx-screw-6-32-pitch?_pos=1&_sid=fafbe2e7d&_ss=r https://thetruelink.com/products/button-head-torx-screw-6-32-pitch?_pos=1&_sid=fafbe2e7d&_ss=r]

Pivot Sex Bolt:<br>
Select .375 [https://thetruelink.com/products/3-16-sex-bolt-gray-finish?_pos=1&_sid=59c550db5&_ss=r https://thetruelink.com/products/3-16-sex-bolt-gray-finish?_pos=1&_sid=59c550db5&_ss=r]

Washer:<br>
Select .016 [https://thetruelink.com/products/375-x-188-phosphorus-bronze-washers?_pos=1&_sid=dc543b96b&_ss=r https://thetruelink.com/products/375-x-188-phosphorus-bronze-washers?_pos=1&_sid=dc543b96b&_ss=r]

Zen Pin:<br>
Select .1565 [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=ff90b42ce&_ss=r https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=ff90b42ce&_ss=r]

==History==

==Modding==

The Replicant is a [[Construction#Sandwich]] balisong. Because of this design, it is easy to swap out components like the scales or spacers. As a result, many people have taken to modding their Replicants. Additionally, the Replicant has been around for a long time, giving modders plenty of time to develop custom parts for it.

===Trivia===

====Zen Pins Pressing Into Liners====

Over time, the zen pins will press into the liners, shrinking the space between the liners and the blade. As a result, you will need to use thinner washers or loosen your zen pin screws.

Balisong List

2026-06-01T19:50:08Z

DexyStorm: remove unnecessary 'x' from balix telesto bushing measurement

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Ultem Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 4.016x4.80x7.001
|
| 6.320x2.00x3.413x5.50x7.725
| 6.314x2.03x4.805x7.61x9.464
| 0.494x5.20x10.001
|-
| rowspan="23" | [[LDY]]
| [[LDY Corvus|Corvus]]
| 440C; 3CR13
| [[Construction#Channel|Channel]]
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus EVO|Cygnus EVO]]
| 440C
|
| 6AL-4V Ti + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank-P|Frank-P]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="32" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
| 6.341x2.03x3.382x6.07x8.211
| 6.338x1.98x4.758x8.00x10.090
| 0.702x4.90x10.018
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
| 7.799x1.83x3.353x4.90x6.577
| 7.780x1.84x4.766x8.86x10.796
| 0.404x4.89x9.44
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Main Page

2026-05-28T11:49:31Z

DexyStorm: add link with contact info

__NOTOC__

== Welcome to the Balisong Wiki ==

=THE BALISONG WIKI WILL SOON CHANGE ITS URL. JOIN THE DISCORD TO BE INFORMED ABOUT THE NEW URL ONCE IT IS ANNOUNCED OR SEND ME A MESSAGE AND I'LL RESPOND TO YOU ONCE THE NEW URL IS PUBLIC. CONTACT INFO CAN BE FOUND HERE: [[#Contact]]=

The Balisong Wiki is supposed to be a one-stop hub for everything balisong related.


= Using The Balisong Wiki =

<div style="display: flex; flex-wrap: wrap; gap: 2em; align-items: flex-start; margin-top: 1em;">


<div style="flex: 1; min-width: 300px;">

===Reading===

<p>If are not interested in contributing and just want quick access to information, use the search bar at the top right of the screen. Alternatively, here are some articles that might interest you.</p>

<p>[[Balisong_List|Balisong List]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A comprehensive list of balisongs and their components.</div>

<p>[[Community]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A page dedicated to listing places where the community is most active.</div>

<p>[[Meta]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Some trivia and general information about the Balisong Wiki itself.</div>

<p>[[Pivot_System|Pivot System]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A list on pivot systems and written tutorials how to tune them.</div>

<p>[[Frequently_Asked_Questions|Frequently Asked Questions]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Some frequently asked questions and the answers to them.</div>

</div>


<div style="flex: 1; min-width: 300px;">

===Contributing===

There are two main ways in which you can contribute to the Balisong Wiki.

<p>[[Edit Guide]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A guide on how to edit the Balisong Wiki.</div>

<p>[https://ko-fi.com/dexystorm/donate Donations]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Donations will mainly go towards paying for a better server, more storage and renting out Domain names.</div>

</div>

</div>


=Contact=

There are multiple ways to contact the admin team and/or the owner.

<div style="display: flex; flex-wrap: wrap; gap: 2em; align-items: flex-start; margin-top: 1em;">


<div style="flex: 1; min-width: 300px;">

<p>[https://discord.gg/Jyggahn5B7 Discord Server]</p>
<div style="margin-left: 1.5em; font-size: 90%;">The best way to get in touch is through the Balisong Wiki Discord server.</div>

<p>[https://discord.com/users/336184339043713034 Discord Direct Message]</p>
<div style="margin-left: 1.5em; font-size: 90%;">I will not accept any friend requests, but I will respond to all direct message requests. In case the direct link above does not work, my username on Discord is "DexyStorm".</div>

<p>[mailto:dexystormlp@gmail.com E-Mail]</p>
<div style="margin-left: 1.5em; font-size: 90%;">If you do not have a Discord account, you can also contact me via E-Mail: dexystormlp@gmail.com</div>

</div>


<div style="flex: 1; min-width: 300px;">

<p>[https://www.instagram.com/dexystorm/ Instagram account]</p>
<div style="margin-left: 1.5em; font-size: 90%;">If you prefer to not use E-Mails, i also have an Instagram account.</div>

<p>[https://www.reddit.com/user/Dexy_Storm/ Reddit]</p>
<div style="margin-left: 1.5em; font-size: 90%;">You can contact me through direct messages on Reddit.</div>

<p>[[User_talk:DexyStorm|The Owner's Talk Page]] </p>
<div style="margin-left: 1.5em; font-size: 90%;">Please keep in mind that everything that you post on my Talk page will be publicly visible.
</div>

</div>
</div>

Main Page

2026-05-28T11:48:31Z

DexyStorm: info about new URL

__NOTOC__

== Welcome to the Balisong Wiki ==

=THE BALISONG WIKI WILL SOON CHANGE ITS URL. JOIN THE DISCORD TO BE INFORMED ABOUT THE NEW URL ONCE IT IS ANNOUNCED OR SEND ME A MESSAGE AND I'LL RESPOND TO YOU ONCE THE NEW URL IS PUBLIC=

The Balisong Wiki is supposed to be a one-stop hub for everything balisong related.


= Using The Balisong Wiki =

<div style="display: flex; flex-wrap: wrap; gap: 2em; align-items: flex-start; margin-top: 1em;">


<div style="flex: 1; min-width: 300px;">

===Reading===

<p>If are not interested in contributing and just want quick access to information, use the search bar at the top right of the screen. Alternatively, here are some articles that might interest you.</p>

<p>[[Balisong_List|Balisong List]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A comprehensive list of balisongs and their components.</div>

<p>[[Community]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A page dedicated to listing places where the community is most active.</div>

<p>[[Meta]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Some trivia and general information about the Balisong Wiki itself.</div>

<p>[[Pivot_System|Pivot System]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A list on pivot systems and written tutorials how to tune them.</div>

<p>[[Frequently_Asked_Questions|Frequently Asked Questions]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Some frequently asked questions and the answers to them.</div>

</div>


<div style="flex: 1; min-width: 300px;">

===Contributing===

There are two main ways in which you can contribute to the Balisong Wiki.

<p>[[Edit Guide]]</p>
<div style="margin-left: 1.5em; font-size: 90%;">A guide on how to edit the Balisong Wiki.</div>

<p>[https://ko-fi.com/dexystorm/donate Donations]</p>
<div style="margin-left: 1.5em; font-size: 90%;">Donations will mainly go towards paying for a better server, more storage and renting out Domain names.</div>

</div>

</div>


=Contact=

There are multiple ways to contact the admin team and/or the owner.

<div style="display: flex; flex-wrap: wrap; gap: 2em; align-items: flex-start; margin-top: 1em;">


<div style="flex: 1; min-width: 300px;">

<p>[https://discord.gg/Jyggahn5B7 Discord Server]</p>
<div style="margin-left: 1.5em; font-size: 90%;">The best way to get in touch is through the Balisong Wiki Discord server.</div>

<p>[https://discord.com/users/336184339043713034 Discord Direct Message]</p>
<div style="margin-left: 1.5em; font-size: 90%;">I will not accept any friend requests, but I will respond to all direct message requests. In case the direct link above does not work, my username on Discord is "DexyStorm".</div>

<p>[mailto:dexystormlp@gmail.com E-Mail]</p>
<div style="margin-left: 1.5em; font-size: 90%;">If you do not have a Discord account, you can also contact me via E-Mail: dexystormlp@gmail.com</div>

</div>


<div style="flex: 1; min-width: 300px;">

<p>[https://www.instagram.com/dexystorm/ Instagram account]</p>
<div style="margin-left: 1.5em; font-size: 90%;">If you prefer to not use E-Mails, i also have an Instagram account.</div>

<p>[https://www.reddit.com/user/Dexy_Storm/ Reddit]</p>
<div style="margin-left: 1.5em; font-size: 90%;">You can contact me through direct messages on Reddit.</div>

<p>[[User_talk:DexyStorm|The Owner's Talk Page]] </p>
<div style="margin-left: 1.5em; font-size: 90%;">Please keep in mind that everything that you post on my Talk page will be publicly visible.
</div>

</div>
</div>

Pivot System

2026-05-26T14:43:27Z

DexyStorm: fix linking

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Pivot_System#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Loose Tolerances With Undersized Bushing====

If you have confirmed that your bushing is undersized but you still have a lot of play when you crank the screws, then your sex bolt is probably too long.
The sex bolt should not extend past the second handle halve, but rather sit recessed within it.<br>
To shorten the sex bolt, just use the same technique as described in the [[#Lapping Methods]] chapters.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washer=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Pivot System

2026-05-26T14:42:31Z

DexyStorm: add Loose Tolerances With Undersized Bushing

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Pivot_System#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Loose Tolerances With Undersized Bushing====

If you have confirmed that your bushing is undersized but you still have a lot of play when you crank the screws, then your sex bolt is probably too long.
The sex bolt should not extend past the second handle halve, but rather sit recessed within it.<br>
To shorten the sex bolt, just use the same technique as described in the [[Lapping Methods]] chapters.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washer=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Pivot System

2026-05-26T11:02:16Z

DexyStorm: change Washer in header from plural to singular

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Pivot_System#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washer=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Pivot System

2026-05-11T10:50:39Z

DexyStorm: fix linking

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Pivot_System#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washers=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Edit Guide

2026-05-03T17:55:19Z

DexyStorm: fix capitalization of titles

==The Rules==

Thank you for showing interest in contributing content to the Balisong Wiki!

Please read the [[Code Of Conduct]] before making any changes to the Balisong Wiki.

==Account Creation==

You do not need an account to edit the wiki, but please keep in mind that your current public IP address will be visible once you publish a change if you are not logged into an account.
An E-Mail address is not required, just your username and password. When creating a password, make sure to remember it well, as there is currently no automated way to reset it. If you need help recovering your account, please [[Main_Page#Contact|contact the owner]].

==Formatting==

===Disable markup===

Mediawiki uses a custom markup language known as Wikitext which is similar to Markdown. It allows users to format text, create links, build tables and structure content using plain text syntax.

If you want your text to not get formatted by Wikitext, you can write it between two nowiki tags. For example<br>

<nowiki><nowiki>[https://www.google.com/ https://www.google.com/]</nowiki></nowiki>

will look like this:<br>

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

instead of being a clickable link to Google like this:<br>

[https://www.google.com/ https://www.google.com/]

===Indentation===

If you want your text to be segregated because you want to draw extra attention to it, you can write that important text in a new line and insert a space before your text. Mediawiki will draw a rectangle around your text and change the font to make it stand out more.

Some very important and interesting text.

===Headings===

====Spacing====

Always leave one empty line before and after each heading, like this:

Text<br>
=New Heading=<br>
Text

====Heading Counter====

The Balisong Wiki supports automatic counting of the headings. There is no need to manually number them. Once you are done with editing an article, the heading numbers will automatically be applied.

====Creating Headings====

To create headings, write the text of the heading between = like this:<br>

<nowiki>=First Heading=</nowiki>

You can make Sub-Headings by increasing the number of =<br>

<nowiki>==Sub-Heading for first Heading==</nowiki>

<nowiki>===Sub-Sub-Heading for first Heading===</nowiki>

====Disable Table Of Contents====

Articles with many chapters will have an automatic table of contents on the top left of that article. To disable the table of contents, put this line as the very first line of the article on which you want to disable this feature

<nowiki>__NOTOC__ </nowiki>

===Dates===

Dates should be written in [https://en.wikipedia.org/wiki/ISO_8601 ISO 8601] standard form.

Here are some examples:<br>

2024-12-30

2022-06-01

2020-01-23

===Break===

If you want to write text in a new line, but do not want the extra empty line that comes with it, you can use the <nowiki><br></nowiki> tag at the end of your line, like this:

<nowiki>Text<br>
Text</nowiki>

And it will be rendered like this:

Text<br>
Text

==Linking==

In order to create a link to a different article, or a different website, you will need to use square brackets

<nowiki>[]</nowiki>

===Spaces===

If an article you want to link to has spaces, for example the Balisong List, just use underscores for those spaces<br>

<nowiki>[[Balisong_List]]</nowiki>

And it will be rendered like this:

[[Balisong_List]]

===Internal===

If you want to link to another article within the Balisong Wiki, write the name of the article between two square brackets like this:

<nowiki>[[Sandbox]]</nowiki>

And it will be rendered like this:

[[Sandbox]]

====Specific section====



=====To Another Article=====

If you want to link to a specific section, write the name of the article, then a pound symbol (#) then the name of the section.

<nowiki>[[Pin_System#Screw_Zen]]</nowiki>

And it will be rendered like this:

[[Pin_System#Screw_Zen]]

=====To The Same Article=====

If you want to link to a same section of the article that you are currently editing, you can leave the linking of the article part out, and just write the pund symbol (#) with the name of the section.<br>
This will link to the first section of this article<br>

<nowiki>[[#Account_creation]]</nowiki>

And it will be rendered like this:

[[#Account_creation]]

===Pipe===

Adding a pipe symbol (|) to the end of your internal linking enables you to write a custom name for the linking. This can be useful to slightly adjust the name of the link so that sentences flow better, or to remove the underscore that is caused by linking

<nowiki>[[Balisong_list|Balisong List]]</nowiki>

Will be rendered as

[[Balisong_list|Balisong List]]

Note: When linking to a chapter, please try to keep the original formating of the link (for example [[#Pipe]] instead of using a custom name, If you must use a custom name, at the very least, include the pund (#) in the link to indicate that it leads to a specific chapter. This helps readers recognize that the link points to a section they might have already seen.

===External===

If you want to link to a different website, for example to show the reader where they can buy a specific bushing, put your link in only 1 set of square brackets

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]

If you want to give your link a name, add a space after the link and add a name.

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.350mm OD bushings]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.350mm OD bushings]

If you want the link to be visible, just write the same link twice in the square brackets with a space in-between the two links.

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

And it will be rendered like this:

[https://www.google.com/ https://www.google.com/]

==Tables==

Tables can be either edited by hand (not recommended), or a table generator can be used. We recommend this [https://www.tablesgenerator.com/mediawiki_tables# table generator].
If you wish to edit this table, copy it, go to the mentioned website, select "MediaWiki" which should be in the bar located at the very top of the page. After that, click "File" in the top left, click "Paste table data..." and paste it in. Wait a couple of seconds and then click the blue "Load" button. After that feel free to make any changes you deem neccessary. After you've adjusted the table, scroll all the way down and click on "Generate" button which is on the left hand side of the screen and wait a couple of seconds as generating a big table can take some time, especially if your device is slow. After that click on the green "Copy to clipboard" button which is on the right hand side of your screen, or just copy the whole code which is in the window right under the gray "'''Result''' (click "Generate" to refresh)" text. After that, delete the old table from this wiki and paste in your newly edited table.

===Formatting The Balisong List===

====Order====

If the list does not have a specific order, like the [[Balisong_List]], please list the entries in alphabetical order.

====Connecting Cells====

If you want to connect cells, please use the [https://www.tablesgenerator.com/mediawiki_tables# table generator]. Select all the cells that you want to connect by dragging your cursor over them. The cells should now have a yellow background. Now click the black button that has two arrows pointing to each other. The button should be at the top of your screen and should look like this:

[[File:Merge_Cells_Button.png]]

====Combining Materials====

If a balisong uses a combination of materials, for example in its handles, write a + between the materials.

TI+G10

====Or====

If you want to say that a balisong can use different materials, write a slash between the materials

G10/CF

====Live Blade VS Trainer====

Try to avoid creating separate entries into the Balisong list for live blades and trainers unless absolutely necessary.
If the live and trainer versions of a balisong differ in weight, material or other properties, use a semicolon (;) to separate the information within the same entry, but always list the live blade information first.

AEB-L;410

==Naming Conventions==

These naming conventions have been created to make page names more consistent, make it easiert for users to find pages and and to make linking easier.<br>
These rules apply to page titles, headings and file names, although headings follow a slightly looser version of these rules.

- Every word must be capitalized, even small words like "of" or "and", unless a name is intentionally written in lowecase, for example "iPhone".

- Always use singular instead of plural. For example "Washer" instead of "Washers".

- Use nouns, not verbs. Instead of "Tuning", use "Tune". A good rule of thumb for this is "Name the thing, not the action".

- Avoid unnecessary words. For example "Zen Pin" instead of "About The Zen Pin Mechanism"

==Creating A New Page==

Before you create a new article, please check whether that article already exists or not. The search bar at the top can be a good tool for that.

If you have made sure that the page you want to create doesnt already exist, you can create the article by opening the base link of this wiki (balisong.info) and append a forward slash (/) and append the name of the article you want to create. For example if you want to create an article called Banana, you would open this link:

http://balisong.info/Banana

After that you have to decide if you want to use the visual editor (not recommended), or the source editor. If you want to use the visual editor, click on "Create". If you want to use the source editor, click on "Create source". The next steps are almost identical with just editing an article, so please read [[Edit_Guide#Editing An Article | #Editing An Article]].

==Editing An Article==

If you want to edit an article, you need to click on the "Edit" or "Edit Source" button. They are usually somewhere on the top right of your screen.

===Source Editor===

If you have clicked the "Edit source" button, a big box will appear in which you can write everything that you know about the topic of the article. If you want to see the changes to the article, scroll to the bottom of the page and click on the "Show preview" button. This will reload the article and show you the text with all the rendered Wikitext code that you have written.
After you have filled the article with information, scroll to the bottom of the page, and write a summary in the "Summary" block like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save page". You might also need to fill out an easy captcha for the changes to to live.

===Visual Editor===

The visual editor is not recommended since it has not been tested.

If you have clicked the "Edit" button you can just start writing down everything you know about the topic of the article.
After you have filled the article with information, click the "Save" button, add a summary message like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save Page". You might also need to fill out an easy captcha for the changes to to live.

===Objective Viewpoint===

When writing or editing articles, keep a neutral point of view. Just because you dislike a certaint product, doesn't mean it's objectively bad.

===Do Not Repeat Yourself===

If you want to add something to the wiki that has already been described on a different article, just link to it instead of repeating information that is already on the Balisong Wiki. See [[#Linking]] for a reminder on how to properly link to different articles and chapters.

===Similar Style===

If you are editing an article, check if there are other articles about similar topics and try to mimic that style.

For example if you want to write an article about a balisong, check out the article about the [[MachineWise_Slift_V2]] and try to copy the style that was used there.

==File Uploads==

The Balisong Wiki supports uploading of media. If you want to upload a picture, click on the "Upload file" field, or just click this link: [[Special:Upload]].<br>
Please check out [[#Naming_Conventions]] if you are unsure how to name your files.

===Only Submit Your Own Images===

Please only submit your own images as we do not want to get into trouble with copyright owners.

===Limits===

Please only upload files that are 1920x1080 or smaller. Large pictures take up a lot of ram, potentially making the Balisong Wiki go [https://en.wikipedia.org/wiki/Out_of_memory out of memory]. If you see a screen like this:
[[File:Out_Of_Memory.png]]
Please immediately contact the server owner [[Main_Page#Contact]].

The following sub-headings will containt important information on how to format images. If you want more information not covered in this editing guide, please check out the official Mediawiki guide for images [https://www.mediawiki.org/wiki/Help:Images https://www.mediawiki.org/wiki/Help:Images].

===Embedding===

Instructions for how to embed files on a page are on the file upload page [[Special:Upload]], but in case you want something clearer:<br>
If you want to embeda picture, write 2 brackets, then "File:" followed by the name of the file, including its file extension.
For example like this:

<nowiki>[[File:Slift_V2.png]]</nowiki>

===Stopping Floating Text===

Sometimes text will be rendered around the image which can look very awkward. To stop this from happening, simply add this line right after the image that you want to embed and leave an empty line after it:

<nowiki><div style="clear: both"></div></nowiki>

Which should look like this with the embed image added

<nowiki>[[File:Slift_V2.png]]</div>
<div style="clear: both">
</nowiki>

Or alternatively you use this code and replace the "..." with the embedding link of your image.

<nowiki><div style="overflow: hidden">…</div></nowiki>

With the embed added, it should look like this:

<nowiki><div style="overflow: hidden">[[File:Slift_V2.png]]</div></nowiki>

===Scaling===

====Resizing====

You can scale images by writing a pipe (|) and the ammount of pixels you want, after the embed.

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

====Restrict Image Within Space====

If you need to fit an image within a certain space, you can restrict its height, width, or both. Keep in mind that the aspect ratio will always be preserved.

=====Restricting Image Width=====

If you want to restrict the width, write the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

This will create an image that is at most 200 pixels wide.

=====Restricting Image Height=====

If you want to restrict the height, write a "x", after that the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|x200px]]</nowiki>

This will create an image that is at most 200 pixels high.

=====Restricting Image Both=====

If you want to restrict both, the height and the width, you can use can write the width, followed by a "x", then the height, and at the end, "px"

<nowiki>[[File:Slift_V2.png|150x200px]]</nowiki>

This will create an image that is at most 150 pixels wide and at most 200 pixels high.

===Thumbnail===

You can enable thumbnailing by adding the "thumb" keyword. This will draw a rectangle around the image to visually separate it from the text.

<nowiki>[[File:MachineWise_Slift_V2.jpg|thumb]]</nowiki>

===Alignment===

You can align the picture by adding the location to where it should be aligned

<nowiki>[[File:MachineWise_Slift_V2.jpg|right]]</nowiki>

===Caption===

You can add a cpation, by writing it as the last argument.

<nowiki>[[File:MachineWise_Slift_V2.jpg|Rose Gold Slift V2]]</nowiki>

===Multiple Arguments===

You can use multiple arguments by just chaining them together with pipes (|)

<nowiki>[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">
</nowiki>

This will embed a picture of a [[MachineWise]] [[MachineWise_Slift_V2]] on this page, which will be scaled to 600 pixels, aligned to the center of the screen, have a caption with "Rose Gold Slift V2", will not have any text floating around it and it will look like this:

[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">

==Measurements==

All measurementes must be provided in metric with an optional measurement in imperial in parenthesis. You are allowed to break this rule if you are citing a source (see the next sub-heading [[#Only_submit_your_own_measurements]] for more information).

6.350mm (0.250in)

or just

6.350mm

The unit of measurement is not neccessary, but should still be added if there is enough space for it. If there is no unit after the number, assume Millimeters or Grams depending on context. For example:

6.350 (0.250)

===Only Submit Your Own Measurements===

While manifacturers may provide measurements for their products, they are often times inaccurate. For example: Squid Industries lists their [https://www.squidindustries.co/products/oversized-bushings?variant=44002598682796 Nautilus bushings] as having an [[Pivot_System#Outer_Diameter]] of 0.2482" +/- .0002 OD = 6.30428mm +/- 0.00508, yet [[Pivot_System#Bushing|Pivot_System#Bushings]] with an [[Pivot_System#Outer_Diameter]] of 6.350mm (0.25in) fit perfectly. Similarly, Nabalis markets their [https://nabalis.com/cdn/shop/files/VULP_0f6d9ff8-34ba-4c2b-8775-15e20801042f.jpg?v=1746763288&width=700 bushings as 7mm OD], but actual measurements show an [[Pivot_System#Outer_Diameter]] of 6.985mm.

Because such discrepancies are common, we ask that you only submit measurements that you have personally verified in real life with a measuring device.

===Decimal Places===

Please add as many decimal places for youre measurements, as you can. The standard should be 3 decimal places.

6.326mm

==Comments==

If you want to add text that is only visible when editing the Balisong Wiki, for example when you want to tell another editor why you have done what you did, you can write a comment like so:

<nowiki></nowiki>

==Speculative Articles==

If you are unsure about a specific topic, do not write about it. You are however allowed to leave chapters empty and only write about the parts of the topic you're certain about. For example, if you know a lot about the history of a particular balisong or have interesting trivia, but don't own the knife yourself and therefore can't provide measurements, it's completely acceptable to fill in the History or Trivia chapters, while leaving the Measurements chapter blank.

==Redacted==

Some users prefer not to be included on the Balisong Wiki. Please respect their wishes and avoid writing about them. If mentioning them is absolutely necessary, for example if they have created a balisong, refer to them as {[[Redacted]]} instead of their name, like this:

The balisong was created by <nowiki>{[[Redacted]]}</nowiki>.

For a full list of people who have requested to be excluded from the Balisong Wiki, please read [[Redacted]].

==AI Usage==

Please do not use any form of LLMs/AI to write articles, as they are prone to hallucinations.

==The [[Sandbox]]==

In the [[Sandbox]] you can make and revert edits freely to familiarize yourself with how to make changes to the BalisongWiki with no fear of messing something up.

Edit Guide

2026-05-03T17:54:36Z

DexyStorm: fix capitalization and linking

==The Rules==

Thank you for showing interest in contributing content to the Balisong Wiki!

Please read the [[Code Of Conduct]] before making any changes to the Balisong Wiki.

==Account Creation==

You do not need an account to edit the wiki, but please keep in mind that your current public IP address will be visible once you publish a change if you are not logged into an account.
An E-Mail address is not required, just your username and password. When creating a password, make sure to remember it well, as there is currently no automated way to reset it. If you need help recovering your account, please [[Main_Page#Contact|contact the owner]].

==Formatting==

===Disable markup===

Mediawiki uses a custom markup language known as Wikitext which is similar to Markdown. It allows users to format text, create links, build tables and structure content using plain text syntax.

If you want your text to not get formatted by Wikitext, you can write it between two nowiki tags. For example<br>

<nowiki><nowiki>[https://www.google.com/ https://www.google.com/]</nowiki></nowiki>

will look like this:<br>

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

instead of being a clickable link to Google like this:<br>

[https://www.google.com/ https://www.google.com/]

===Indentation===

If you want your text to be segregated because you want to draw extra attention to it, you can write that important text in a new line and insert a space before your text. Mediawiki will draw a rectangle around your text and change the font to make it stand out more.

Some very important and interesting text.

===Headings===

====Spacing====

Always leave one empty line before and after each heading, like this:

Text<br>
=New Heading=<br>
Text

====Heading Counter====

The Balisong Wiki supports automatic counting of the headings. There is no need to manually number them. Once you are done with editing an article, the heading numbers will automatically be applied.

====Creating Headings====

To create headings, write the text of the heading between = like this:<br>

<nowiki>=First Heading=</nowiki>

You can make Sub-Headings by increasing the number of =<br>

<nowiki>==Sub-Heading for first Heading==</nowiki>

<nowiki>===Sub-Sub-Heading for first Heading===</nowiki>

====Disable Table Of Contents====

Articles with many chapters will have an automatic table of contents on the top left of that article. To disable the table of contents, put this line as the very first line of the article on which you want to disable this feature

<nowiki>__NOTOC__ </nowiki>

===Dates===

Dates should be written in [https://en.wikipedia.org/wiki/ISO_8601 ISO 8601] standard form.

Here are some examples:<br>

2024-12-30

2022-06-01

2020-01-23

===Break===

If you want to write text in a new line, but do not want the extra empty line that comes with it, you can use the <nowiki><br></nowiki> tag at the end of your line, like this:

<nowiki>Text<br>
Text</nowiki>

And it will be rendered like this:

Text<br>
Text

==Linking==

In order to create a link to a different article, or a different website, you will need to use square brackets

<nowiki>[]</nowiki>

===Spaces===

If an article you want to link to has spaces, for example the Balisong List, just use underscores for those spaces<br>

<nowiki>[[Balisong_List]]</nowiki>

And it will be rendered like this:

[[Balisong_List]]

===Internal===

If you want to link to another article within the Balisong Wiki, write the name of the article between two square brackets like this:

<nowiki>[[Sandbox]]</nowiki>

And it will be rendered like this:

[[Sandbox]]

====Specific section====



=====To another article=====

If you want to link to a specific section, write the name of the article, then a pound symbol (#) then the name of the section.

<nowiki>[[Pin_System#Screw_Zen]]</nowiki>

And it will be rendered like this:

[[Pin_System#Screw_Zen]]

=====To the same article=====

If you want to link to a same section of the article that you are currently editing, you can leave the linking of the article part out, and just write the pund symbol (#) with the name of the section.<br>
This will link to the first section of this article<br>

<nowiki>[[#Account_creation]]</nowiki>

And it will be rendered like this:

[[#Account_creation]]

===Pipe===

Adding a pipe symbol (|) to the end of your internal linking enables you to write a custom name for the linking. This can be useful to slightly adjust the name of the link so that sentences flow better, or to remove the underscore that is caused by linking

<nowiki>[[Balisong_list|Balisong List]]</nowiki>

Will be rendered as

[[Balisong_list|Balisong List]]

Note: When linking to a chapter, please try to keep the original formating of the link (for example [[#Pipe]] instead of using a custom name, If you must use a custom name, at the very least, include the pund (#) in the link to indicate that it leads to a specific chapter. This helps readers recognize that the link points to a section they might have already seen.

===External===

If you want to link to a different website, for example to show the reader where they can buy a specific bushing, put your link in only 1 set of square brackets

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]

If you want to give your link a name, add a space after the link and add a name.

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.350mm OD bushings]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.350mm OD bushings]

If you want the link to be visible, just write the same link twice in the square brackets with a space in-between the two links.

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

And it will be rendered like this:

[https://www.google.com/ https://www.google.com/]

==Tables==

Tables can be either edited by hand (not recommended), or a table generator can be used. We recommend this [https://www.tablesgenerator.com/mediawiki_tables# table generator].
If you wish to edit this table, copy it, go to the mentioned website, select "MediaWiki" which should be in the bar located at the very top of the page. After that, click "File" in the top left, click "Paste table data..." and paste it in. Wait a couple of seconds and then click the blue "Load" button. After that feel free to make any changes you deem neccessary. After you've adjusted the table, scroll all the way down and click on "Generate" button which is on the left hand side of the screen and wait a couple of seconds as generating a big table can take some time, especially if your device is slow. After that click on the green "Copy to clipboard" button which is on the right hand side of your screen, or just copy the whole code which is in the window right under the gray "'''Result''' (click "Generate" to refresh)" text. After that, delete the old table from this wiki and paste in your newly edited table.

===Formatting The Balisong List===

====Order====

If the list does not have a specific order, like the [[Balisong_List]], please list the entries in alphabetical order.

====Connecting Cells====

If you want to connect cells, please use the [https://www.tablesgenerator.com/mediawiki_tables# table generator]. Select all the cells that you want to connect by dragging your cursor over them. The cells should now have a yellow background. Now click the black button that has two arrows pointing to each other. The button should be at the top of your screen and should look like this:

[[File:Merge_Cells_Button.png]]

====Combining Materials====

If a balisong uses a combination of materials, for example in its handles, write a + between the materials.

TI+G10

====Or====

If you want to say that a balisong can use different materials, write a slash between the materials

G10/CF

====Live Blade VS Trainer====

Try to avoid creating separate entries into the Balisong list for live blades and trainers unless absolutely necessary.
If the live and trainer versions of a balisong differ in weight, material or other properties, use a semicolon (;) to separate the information within the same entry, but always list the live blade information first.

AEB-L;410

==Naming Conventions==

These naming conventions have been created to make page names more consistent, make it easiert for users to find pages and and to make linking easier.<br>
These rules apply to page titles, headings and file names, although headings follow a slightly looser version of these rules.

- Every word must be capitalized, even small words like "of" or "and", unless a name is intentionally written in lowecase, for example "iPhone".

- Always use singular instead of plural. For example "Washer" instead of "Washers".

- Use nouns, not verbs. Instead of "Tuning", use "Tune". A good rule of thumb for this is "Name the thing, not the action".

- Avoid unnecessary words. For example "Zen Pin" instead of "About The Zen Pin Mechanism"

==Creating A New Page==

Before you create a new article, please check whether that article already exists or not. The search bar at the top can be a good tool for that.

If you have made sure that the page you want to create doesnt already exist, you can create the article by opening the base link of this wiki (balisong.info) and append a forward slash (/) and append the name of the article you want to create. For example if you want to create an article called Banana, you would open this link:

http://balisong.info/Banana

After that you have to decide if you want to use the visual editor (not recommended), or the source editor. If you want to use the visual editor, click on "Create". If you want to use the source editor, click on "Create source". The next steps are almost identical with just editing an article, so please read [[Edit_Guide#Editing An Article | #Editing An Article]].

==Editing An Article==

If you want to edit an article, you need to click on the "Edit" or "Edit Source" button. They are usually somewhere on the top right of your screen.

===Source Editor===

If you have clicked the "Edit source" button, a big box will appear in which you can write everything that you know about the topic of the article. If you want to see the changes to the article, scroll to the bottom of the page and click on the "Show preview" button. This will reload the article and show you the text with all the rendered Wikitext code that you have written.
After you have filled the article with information, scroll to the bottom of the page, and write a summary in the "Summary" block like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save page". You might also need to fill out an easy captcha for the changes to to live.

===Visual Editor===

The visual editor is not recommended since it has not been tested.

If you have clicked the "Edit" button you can just start writing down everything you know about the topic of the article.
After you have filled the article with information, click the "Save" button, add a summary message like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save Page". You might also need to fill out an easy captcha for the changes to to live.

===Objective Viewpoint===

When writing or editing articles, keep a neutral point of view. Just because you dislike a certaint product, doesn't mean it's objectively bad.

===Do Not Repeat Yourself===

If you want to add something to the wiki that has already been described on a different article, just link to it instead of repeating information that is already on the Balisong Wiki. See [[#Linking]] for a reminder on how to properly link to different articles and chapters.

===Similar Style===

If you are editing an article, check if there are other articles about similar topics and try to mimic that style.

For example if you want to write an article about a balisong, check out the article about the [[MachineWise_Slift_V2]] and try to copy the style that was used there.

==File Uploads==

The Balisong Wiki supports uploading of media. If you want to upload a picture, click on the "Upload file" field, or just click this link: [[Special:Upload]].<br>
Please check out [[#Naming_Conventions]] if you are unsure how to name your files.

===Only Submit Your Own Images===

Please only submit your own images as we do not want to get into trouble with copyright owners.

===Limits===

Please only upload files that are 1920x1080 or smaller. Large pictures take up a lot of ram, potentially making the Balisong Wiki go [https://en.wikipedia.org/wiki/Out_of_memory out of memory]. If you see a screen like this:
[[File:Out_Of_Memory.png]]
Please immediately contact the server owner [[Main_Page#Contact]].

The following sub-headings will containt important information on how to format images. If you want more information not covered in this editing guide, please check out the official Mediawiki guide for images [https://www.mediawiki.org/wiki/Help:Images https://www.mediawiki.org/wiki/Help:Images].

===Embedding===

Instructions for how to embed files on a page are on the file upload page [[Special:Upload]], but in case you want something clearer:<br>
If you want to embeda picture, write 2 brackets, then "File:" followed by the name of the file, including its file extension.
For example like this:

<nowiki>[[File:Slift_V2.png]]</nowiki>

===Stopping Floating Text===

Sometimes text will be rendered around the image which can look very awkward. To stop this from happening, simply add this line right after the image that you want to embed and leave an empty line after it:

<nowiki><div style="clear: both"></div></nowiki>

Which should look like this with the embed image added

<nowiki>[[File:Slift_V2.png]]</div>
<div style="clear: both">
</nowiki>

Or alternatively you use this code and replace the "..." with the embedding link of your image.

<nowiki><div style="overflow: hidden">…</div></nowiki>

With the embed added, it should look like this:

<nowiki><div style="overflow: hidden">[[File:Slift_V2.png]]</div></nowiki>

===Scaling===

====Resizing====

You can scale images by writing a pipe (|) and the ammount of pixels you want, after the embed.

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

====Restrict Image Within Space====

If you need to fit an image within a certain space, you can restrict its height, width, or both. Keep in mind that the aspect ratio will always be preserved.

=====Restricting Image Width=====

If you want to restrict the width, write the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

This will create an image that is at most 200 pixels wide.

=====Restricting Image Height=====

If you want to restrict the height, write a "x", after that the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|x200px]]</nowiki>

This will create an image that is at most 200 pixels high.

=====Restricting Image Both=====

If you want to restrict both, the height and the width, you can use can write the width, followed by a "x", then the height, and at the end, "px"

<nowiki>[[File:Slift_V2.png|150x200px]]</nowiki>

This will create an image that is at most 150 pixels wide and at most 200 pixels high.

===Thumbnail===

You can enable thumbnailing by adding the "thumb" keyword. This will draw a rectangle around the image to visually separate it from the text.

<nowiki>[[File:MachineWise_Slift_V2.jpg|thumb]]</nowiki>

===Alignment===

You can align the picture by adding the location to where it should be aligned

<nowiki>[[File:MachineWise_Slift_V2.jpg|right]]</nowiki>

===Caption===

You can add a cpation, by writing it as the last argument.

<nowiki>[[File:MachineWise_Slift_V2.jpg|Rose Gold Slift V2]]</nowiki>

===Multiple Arguments===

You can use multiple arguments by just chaining them together with pipes (|)

<nowiki>[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">
</nowiki>

This will embed a picture of a [[MachineWise]] [[MachineWise_Slift_V2]] on this page, which will be scaled to 600 pixels, aligned to the center of the screen, have a caption with "Rose Gold Slift V2", will not have any text floating around it and it will look like this:

[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">

==Measurements==

All measurementes must be provided in metric with an optional measurement in imperial in parenthesis. You are allowed to break this rule if you are citing a source (see the next sub-heading [[#Only_submit_your_own_measurements]] for more information).

6.350mm (0.250in)

or just

6.350mm

The unit of measurement is not neccessary, but should still be added if there is enough space for it. If there is no unit after the number, assume Millimeters or Grams depending on context. For example:

6.350 (0.250)

===Only Submit Your Own Measurements===

While manifacturers may provide measurements for their products, they are often times inaccurate. For example: Squid Industries lists their [https://www.squidindustries.co/products/oversized-bushings?variant=44002598682796 Nautilus bushings] as having an [[Pivot_System#Outer_Diameter]] of 0.2482" +/- .0002 OD = 6.30428mm +/- 0.00508, yet [[Pivot_System#Bushing|Pivot_System#Bushings]] with an [[Pivot_System#Outer_Diameter]] of 6.350mm (0.25in) fit perfectly. Similarly, Nabalis markets their [https://nabalis.com/cdn/shop/files/VULP_0f6d9ff8-34ba-4c2b-8775-15e20801042f.jpg?v=1746763288&width=700 bushings as 7mm OD], but actual measurements show an [[Pivot_System#Outer_Diameter]] of 6.985mm.

Because such discrepancies are common, we ask that you only submit measurements that you have personally verified in real life with a measuring device.

===Decimal Places===

Please add as many decimal places for youre measurements, as you can. The standard should be 3 decimal places.

6.326mm

==Comments==

If you want to add text that is only visible when editing the Balisong Wiki, for example when you want to tell another editor why you have done what you did, you can write a comment like so:

<nowiki></nowiki>

==Speculative Articles==

If you are unsure about a specific topic, do not write about it. You are however allowed to leave chapters empty and only write about the parts of the topic you're certain about. For example, if you know a lot about the history of a particular balisong or have interesting trivia, but don't own the knife yourself and therefore can't provide measurements, it's completely acceptable to fill in the History or Trivia chapters, while leaving the Measurements chapter blank.

==Redacted==

Some users prefer not to be included on the Balisong Wiki. Please respect their wishes and avoid writing about them. If mentioning them is absolutely necessary, for example if they have created a balisong, refer to them as {[[Redacted]]} instead of their name, like this:

The balisong was created by <nowiki>{[[Redacted]]}</nowiki>.

For a full list of people who have requested to be excluded from the Balisong Wiki, please read [[Redacted]].

==AI Usage==

Please do not use any form of LLMs/AI to write articles, as they are prone to hallucinations.

==The [[Sandbox]]==

In the [[Sandbox]] you can make and revert edits freely to familiarize yourself with how to make changes to the BalisongWiki with no fear of messing something up.

Edit Guide

2026-05-03T17:50:56Z

DexyStorm: small update to external linking section

==The Rules==

Thank you for showing interest in contributing content to the Balisong Wiki!

Please read the [[Code Of Conduct]] before making any changes to the Balisong Wiki.

==Account Creation==

You do not need an account to edit the wiki, but please keep in mind that your current public IP address will be visible once you publish a change if you are not logged into an account.
An E-Mail address is not required, just your username and password. When creating a password, make sure to remember it well, as there is currently no automated way to reset it. If you need help recovering your account, please [[Main_Page#Contact|contact the owner]].

==Formatting==

===Disable markup===

Mediawiki uses a custom markup language known as Wikitext which is similar to Markdown. It allows users to format text, create links, build tables and structure content using plain text syntax.

If you want your text to not get formatted by Wikitext, you can write it between two nowiki tags. For example<br>

<nowiki><nowiki>[https://www.google.com/ https://www.google.com/]</nowiki></nowiki>

will look like this:<br>

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

instead of being a clickable link to Google like this:<br>

[https://www.google.com/ https://www.google.com/]

===Indentation===

If you want your text to be segregated because you want to draw extra attention to it, you can write that important text in a new line and insert a space before your text. Mediawiki will draw a rectangle around your text and change the font to make it stand out more.

Some very important and interesting text.

===Headings===

====Spacing====

Always leave one empty line before and after each heading, like this:

Text<br>
=New Heading=<br>
Text

====Heading Counter====

The Balisong Wiki supports automatic counting of the headings. There is no need to manually number them. Once you are done with editing an article, the heading numbers will automatically be applied.

====Creating Headings====

To create headings, write the text of the heading between = like this:<br>

<nowiki>=First Heading=</nowiki>

You can make Sub-Headings by increasing the number of =<br>

<nowiki>==Sub-Heading for first Heading==</nowiki>

<nowiki>===Sub-Sub-Heading for first Heading===</nowiki>

====Disable Table Of Contents====

Articles with many chapters will have an automatic table of contents on the top left of that article. To disable the table of contents, put this line as the very first line of the article on which you want to disable this feature

<nowiki>__NOTOC__ </nowiki>

===Dates===

Dates should be written in [https://en.wikipedia.org/wiki/ISO_8601 ISO 8601] standard form.

Here are some examples:<br>

2024-12-30

2022-06-01

2020-01-23

===Break===

If you want to write text in a new line, but do not want the extra empty line that comes with it, you can use the <nowiki><br></nowiki> tag at the end of your line, like this:

<nowiki>Text<br>
Text</nowiki>

And it will be rendered like this:

Text<br>
Text

==Linking==

In order to create a link to a different article, or a different website, you will need to use square brackets

<nowiki>[]</nowiki>

===Spaces===

If an article you want to link to has spaces, for example the Balisong List, just use underscores for those spaces<br>

<nowiki>[[Balisong_List]]</nowiki>

And it will be rendered like this:

[[Balisong_List]]

===Internal===

If you want to link to another article within the Balisong Wiki, write the name of the article between two square brackets like this:

<nowiki>[[Sandbox]]</nowiki>

And it will be rendered like this:

[[Sandbox]]

====Specific section====



=====To another article=====

If you want to link to a specific section, write the name of the article, then a pound symbol (#) then the name of the section.

<nowiki>[[Pin_System#Screw_Zen]]</nowiki>

And it will be rendered like this:

[[Pin_System#Screw_Zen]]

=====To the same article=====

If you want to link to a same section of the article that you are currently editing, you can leave the linking of the article part out, and just write the pund symbol (#) with the name of the section.<br>
This will link to the first section of this article<br>

<nowiki>[[#Account_creation]]</nowiki>

And it will be rendered like this:

[[#Account_creation]]

===Pipe===

Adding a pipe symbol (|) to the end of your internal linking enables you to write a custom name for the linking. This can be useful to slightly adjust the name of the link so that sentences flow better, or to remove the underscore that is caused by linking

<nowiki>[[Balisong_list|Balisong List]]</nowiki>

Will be rendered as

[[Balisong_list|Balisong List]]

Note: When linking to a chapter, please try to keep the original formating of the link (for example [[#Pipe]] instead of using a custom name, If you must use a custom name, at the very least, include the pund (#) in the link to indicate that it leads to a specific chapter. This helps readers recognize that the link points to a section they might have already seen.

===External===

If you want to link to a different website, for example to show the reader where they can buy a specific bushing, put your link in only 1 set of square brackets

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]

If you want to give your link a name, add a space after the link and add a name.

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.350mm OD bushings]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.350mm OD bushings]

If you want the link to be visible, just write the same link twice in the square brackets with a space in-between the two links.

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

And it will be rendered like this:

[https://www.google.com/ https://www.google.com/]

==Tables==

Tables can be either edited by hand (not recommended), or a table generator can be used. We recommend this [https://www.tablesgenerator.com/mediawiki_tables# table generator].
If you wish to edit this table, copy it, go to the mentioned website, select "MediaWiki" which should be in the bar located at the very top of the page. After that, click "File" in the top left, click "Paste table data..." and paste it in. Wait a couple of seconds and then click the blue "Load" button. After that feel free to make any changes you deem neccessary. After you've adjusted the table, scroll all the way down and click on "Generate" button which is on the left hand side of the screen and wait a couple of seconds as generating a big table can take some time, especially if your device is slow. After that click on the green "Copy to clipboard" button which is on the right hand side of your screen, or just copy the whole code which is in the window right under the gray "'''Result''' (click "Generate" to refresh)" text. After that, delete the old table from this wiki and paste in your newly edited table.

===Formatting The Balisong List===

====Order====

If the list does not have a specific order, like the [[Balisong_List]], please list the entries in alphabetical order.

====Connecting Cells====

If you want to connect cells, please use the [https://www.tablesgenerator.com/mediawiki_tables# table generator]. Select all the cells that you want to connect by dragging your cursor over them. The cells should now have a yellow background. Now click the black button that has two arrows pointing to each other. The button should be at the top of your screen and should look like this:

[[File:Merge_Cells_Button.png]]

====Combining Materials====

If a balisong uses a combination of materials, for example in its handles, write a + between the materials.

TI+G10

====Or====

If you want to say that a balisong can use different materials, write a slash between the materials

G10/CF

====Live Blade VS Trainer====

Try to avoid creating separate entries into the Balisong list for live blades and trainers unless absolutely necessary.
If the live and trainer versions of a balisong differ in weight, material or other properties, use a semicolon (;) to separate the information within the same entry, but always list the live blade information first.

AEB-L;410

==Naming Conventions==

These naming conventions have been created to make page names more consistent, make it easiert for users to find pages and and to make linking easier.<br>
These rules apply to page titles, headings and file names, although headings follow a slightly looser version of these rules.

- Every word must be capitalized, even small words like "of" or "and", unless a name is intentionally written in lowecase, for example "iPhone".

- Always use singular instead of plural. For example "Washer" instead of "Washers".

- Use nouns, not verbs. Instead of "Tuning", use "Tune". A good rule of thumb for this is "Name the thing, not the action".

- Avoid unnecessary words. For example "Zen Pin" instead of "About The Zen Pin Mechanism"

==Creating a new Page==

Before you create a new article, please check whether that article already exists or not. The search bar at the top can be a good tool for that.

If you have made sure that the page you want to create doesnt already exist, you can create the article by opening the base link of this wiki (balisong.info) and append a forward slash (/) and append the name of the article you want to create. For example if you want to create an article called Banana, you would open this link:

http://balisong.info/Banana

After that you have to decide if you want to use the visual editor (not recommended), or the source editor. If you want to use the visual editor, click on "Create". If you want to use the source editor, click on "Create source". The next steps are almost identical with just editing an article, so please read the next section.

==Editing an article==

If you want to edit an article, you need to click on the "Edit" or "Edit Source" button. They are usually somewhere on the top right of your screen.

===Source Editor===

If you have clicked the "Edit source" button, a big box will appear in which you can write everything that you know about the topic of the article. If you want to see the changes to the article, scroll to the bottom of the page and click on the "Show preview" button. This will reload the article and show you the text with all the rendered Wikitext code that you have written.
After you have filled the article with information, scroll to the bottom of the page, and write a summary in the "Summary" block like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save page". You might also need to fill out an easy captcha for the changes to to live.

===Visual Editor===

The visual editor is not recommended since it has not been tested.

If you have clicked the "Edit" button you can just start writing down everything you know about the topic of the article.
After you have filled the article with information, click the "Save" button, add a summary message like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save Page". You might also need to fill out an easy captcha for the changes to to live.

===Objective Viewpoint===

When writing or editing articles, keep a neutral point of view. Just because you dislike a certaint product, doesn't mean it's objectively bad.

===Do Not Repeat Yourself===

If you want to add something to the wiki that has already been described on a different article, just link to it instead of repeating information that is already on the Balisong Wiki. See [[#Linking]] for a reminder on how to properly link to different articles and chapters.

===Similar Style===

If you are editing an article, check if there are other articles about similar topics and try to mimic that style.

For example if you want to write an article about a balisong, check out the article about the [[MachineWise_Slift_V2]] and try to copy the style that was used there.

==File Uploads==

The Balisong Wiki supports uploading of media. If you want to upload a picture, click on the "Upload file" field, or just click this link: [[Special:Upload]].<br>
Please check out [[#Naming_Conventions]] if you are unsure how to name your files.

===Only Submit Your Own Images===

Please only submit your own images as we do not want to get into trouble with copyright owners.

===Limits===

Please only upload files that are 1920x1080 or smaller. Large pictures take up a lot of ram, potentially making the Balisong Wiki go [https://en.wikipedia.org/wiki/Out_of_memory out of memory]. If you see a screen like this:
[[File:Out_Of_Memory.png]]
Please immediately contact the server owner [[Main_Page#Contact]].

The following sub-headings will containt important information on how to format images. If you want more information not covered in this editing guide, please check out the official Mediawiki guide for images [https://www.mediawiki.org/wiki/Help:Images https://www.mediawiki.org/wiki/Help:Images].

===Embedding===

Instructions for how to embed files on a page are on the file upload page [[Special:Upload]], but in case you want something clearer:<br>
If you want to embeda picture, write 2 brackets, then "File:" followed by the name of the file, including its file extension.
For example like this:

<nowiki>[[File:Slift_V2.png]]</nowiki>

===Stopping Floating Text===

Sometimes text will be rendered around the image which can look very awkward. To stop this from happening, simply add this line right after the image that you want to embed and leave an empty line after it:

<nowiki><div style="clear: both"></div></nowiki>

Which should look like this with the embed image added

<nowiki>[[File:Slift_V2.png]]</div>
<div style="clear: both">
</nowiki>

Or alternatively you use this code and replace the "..." with the embedding link of your image.

<nowiki><div style="overflow: hidden">…</div></nowiki>

With the embed added, it should look like this:

<nowiki><div style="overflow: hidden">[[File:Slift_V2.png]]</div></nowiki>

===Scaling===

====Resizing====

You can scale images by writing a pipe (|) and the ammount of pixels you want, after the embed.

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

====Restrict Image Within Space====

If you need to fit an image within a certain space, you can restrict its height, width, or both. Keep in mind that the aspect ratio will always be preserved.

=====Restricting Image Width=====

If you want to restrict the width, write the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

This will create an image that is at most 200 pixels wide.

=====Restricting Image Height=====

If you want to restrict the height, write a "x", after that the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|x200px]]</nowiki>

This will create an image that is at most 200 pixels high.

=====Restricting Image Both=====

If you want to restrict both, the height and the width, you can use can write the width, followed by a "x", then the height, and at the end, "px"

<nowiki>[[File:Slift_V2.png|150x200px]]</nowiki>

This will create an image that is at most 150 pixels wide and at most 200 pixels high.

===Thumbnail===

You can enable thumbnailing by adding the "thumb" keyword. This will draw a rectangle around the image to visually separate it from the text.

<nowiki>[[File:MachineWise_Slift_V2.jpg|thumb]]</nowiki>

===Alignment===

You can align the picture by adding the location to where it should be aligned

<nowiki>[[File:MachineWise_Slift_V2.jpg|right]]</nowiki>

===Caption===

You can add a cpation, by writing it as the last argument.

<nowiki>[[File:MachineWise_Slift_V2.jpg|Rose Gold Slift V2]]</nowiki>

===Multiple Arguments===

You can use multiple arguments by just chaining them together with pipes (|)

<nowiki>[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">
</nowiki>

This will embed a picture of a [[MachineWise]] [[MachineWise_Slift_V2]] on this page, which will be scaled to 600 pixels, aligned to the center of the screen, have a caption with "Rose Gold Slift V2", will not have any text floating around it and it will look like this:

[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">

==Measurements==

All measurementes must be provided in metric with an optional measurement in imperial in parenthesis. You are allowed to break this rule if you are citing a source (see the next sub-heading [[#Only_submit_your_own_measurements]] for more information).

6.350mm (0.250in)

or just

6.350mm

The unit of measurement is not neccessary, but should still be added if there is enough space for it. If there is no unit after the number, assume Millimeters or Grams depending on context. For example:

6.350 (0.250)

===Only Submit Your Own Measurements===

While manifacturers may provide measurements for their products, they are often times inaccurate. For example: Squid Industries lists their [https://www.squidindustries.co/products/oversized-bushings?variant=44002598682796 Nautilus bushings] as having an [[Pivot_System#Outer_Diameter]] of 0.2482" +/- .0002 OD = 6.30428mm +/- 0.00508, yet [[Pivot_System#Bushing|Pivot_System#Bushings]] with an [[Pivot_System#Outer_Diameter]] of 6.350mm (0.25in) fit perfectly. Similarly, Nabalis markets their [https://nabalis.com/cdn/shop/files/VULP_0f6d9ff8-34ba-4c2b-8775-15e20801042f.jpg?v=1746763288&width=700 bushings as 7mm OD], but actual measurements show an [[Pivot_System#Outer_Diameter]] of 6.985mm.

Because such discrepancies are common, we ask that you only submit measurements that you have personally verified in real life with a measuring device.

===Decimal Places===

Please add as many decimal places for youre measurements, as you can. The standard should be 3 decimal places.

6.326mm

==Comments==

If you want to add text that is only visible when editing the Balisong Wiki, for example when you want to tell another editor why you have done what you did, you can write a comment like so:

<nowiki></nowiki>

==Speculative Articles==

If you are unsure about a specific topic, do not write about it. You are however allowed to leave chapters empty and only write about the parts of the topic you're certain about. For example, if you know a lot about the history of a particular balisong or have interesting trivia, but don't own the knife yourself and therefore can't provide measurements, it's completely acceptable to fill in the History or Trivia chapters, while leaving the Measurements chapter blank.

==Redacted==

Some users prefer not to be included on the Balisong Wiki. Please respect their wishes and avoid writing about them. If mentioning them is absolutely necessary, for example if they have created a balisong, refer to them as {[[Redacted]]} instead of their name, like this:

The balisong was created by <nowiki>{[[Redacted]]}</nowiki>.

For a full list of people who have requested to be excluded from the Balisong Wiki, please read [[Redacted]].

==AI Usage==

Please do not use any form of LLMs/AI to write articles, as they are prone to hallucinations.

==The [[Sandbox]]==

In the [[Sandbox]] you can make and revert edits freely to familiarize yourself with how to make changes to the BalisongWiki with no fear of messing something up.

Edit Guide

2026-05-03T17:48:12Z

DexyStorm: fix showcase of <br> tag

==The Rules==

Thank you for showing interest in contributing content to the Balisong Wiki!

Please read the [[Code Of Conduct]] before making any changes to the Balisong Wiki.

==Account Creation==

You do not need an account to edit the wiki, but please keep in mind that your current public IP address will be visible once you publish a change if you are not logged into an account.
An E-Mail address is not required, just your username and password. When creating a password, make sure to remember it well, as there is currently no automated way to reset it. If you need help recovering your account, please [[Main_Page#Contact|contact the owner]].

==Formatting==

===Disable markup===

Mediawiki uses a custom markup language known as Wikitext which is similar to Markdown. It allows users to format text, create links, build tables and structure content using plain text syntax.

If you want your text to not get formatted by Wikitext, you can write it between two nowiki tags. For example<br>

<nowiki><nowiki>[https://www.google.com/ https://www.google.com/]</nowiki></nowiki>

will look like this:<br>

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

instead of being a clickable link to Google like this:<br>

[https://www.google.com/ https://www.google.com/]

===Indentation===

If you want your text to be segregated because you want to draw extra attention to it, you can write that important text in a new line and insert a space before your text. Mediawiki will draw a rectangle around your text and change the font to make it stand out more.

Some very important and interesting text.

===Headings===

====Spacing====

Always leave one empty line before and after each heading, like this:

Text<br>
=New Heading=<br>
Text

====Heading Counter====

The Balisong Wiki supports automatic counting of the headings. There is no need to manually number them. Once you are done with editing an article, the heading numbers will automatically be applied.

====Creating Headings====

To create headings, write the text of the heading between = like this:<br>

<nowiki>=First Heading=</nowiki>

You can make Sub-Headings by increasing the number of =<br>

<nowiki>==Sub-Heading for first Heading==</nowiki>

<nowiki>===Sub-Sub-Heading for first Heading===</nowiki>

====Disable Table Of Contents====

Articles with many chapters will have an automatic table of contents on the top left of that article. To disable the table of contents, put this line as the very first line of the article on which you want to disable this feature

<nowiki>__NOTOC__ </nowiki>

===Dates===

Dates should be written in [https://en.wikipedia.org/wiki/ISO_8601 ISO 8601] standard form.

Here are some examples:<br>

2024-12-30

2022-06-01

2020-01-23

===Break===

If you want to write text in a new line, but do not want the extra empty line that comes with it, you can use the <nowiki><br></nowiki> tag at the end of your line, like this:

<nowiki>Text<br>
Text</nowiki>

And it will be rendered like this:

Text<br>
Text

==Linking==

In order to create a link to a different article, or a different website, you will need to use square brackets

<nowiki>[]</nowiki>

===Spaces===

If an article you want to link to has spaces, for example the Balisong List, just use underscores for those spaces<br>

<nowiki>[[Balisong_List]]</nowiki>

And it will be rendered like this:

[[Balisong_List]]

===Internal===

If you want to link to another article within the Balisong Wiki, write the name of the article between two square brackets like this:

<nowiki>[[Sandbox]]</nowiki>

And it will be rendered like this:

[[Sandbox]]

====Specific section====



=====To another article=====

If you want to link to a specific section, write the name of the article, then a pound symbol (#) then the name of the section.

<nowiki>[[Pin_System#Screw_Zen]]</nowiki>

And it will be rendered like this:

[[Pin_System#Screw_Zen]]

=====To the same article=====

If you want to link to a same section of the article that you are currently editing, you can leave the linking of the article part out, and just write the pund symbol (#) with the name of the section.<br>
This will link to the first section of this article<br>

<nowiki>[[#Account_creation]]</nowiki>

And it will be rendered like this:

[[#Account_creation]]

===Pipe===

Adding a pipe symbol (|) to the end of your internal linking enables you to write a custom name for the linking. This can be useful to slightly adjust the name of the link so that sentences flow better, or to remove the underscore that is caused by linking

<nowiki>[[Balisong_list|Balisong List]]</nowiki>

Will be rendered as

[[Balisong_list|Balisong List]]

Note: When linking to a chapter, please try to keep the original formating of the link (for example [[#Pipe]] instead of using a custom name, If you must use a custom name, at the very least, include the pund (#) in the link to indicate that it leads to a specific chapter. This helps readers recognize that the link points to a section they might have already seen.

===External===

If you want to link to a different website, for example to show the reader where they can buy a specific bushing, put your link in only 1 set of square brackets

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]

If you want to give your link a name, add a space after the link and add a name.

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.35mm OD bushings]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.35mm OD bushings]

==Tables==

Tables can be either edited by hand (not recommended), or a table generator can be used. We recommend this [https://www.tablesgenerator.com/mediawiki_tables# table generator].
If you wish to edit this table, copy it, go to the mentioned website, select "MediaWiki" which should be in the bar located at the very top of the page. After that, click "File" in the top left, click "Paste table data..." and paste it in. Wait a couple of seconds and then click the blue "Load" button. After that feel free to make any changes you deem neccessary. After you've adjusted the table, scroll all the way down and click on "Generate" button which is on the left hand side of the screen and wait a couple of seconds as generating a big table can take some time, especially if your device is slow. After that click on the green "Copy to clipboard" button which is on the right hand side of your screen, or just copy the whole code which is in the window right under the gray "'''Result''' (click "Generate" to refresh)" text. After that, delete the old table from this wiki and paste in your newly edited table.

===Formatting The Balisong List===

====Order====

If the list does not have a specific order, like the [[Balisong_List]], please list the entries in alphabetical order.

====Connecting Cells====

If you want to connect cells, please use the [https://www.tablesgenerator.com/mediawiki_tables# table generator]. Select all the cells that you want to connect by dragging your cursor over them. The cells should now have a yellow background. Now click the black button that has two arrows pointing to each other. The button should be at the top of your screen and should look like this:

[[File:Merge_Cells_Button.png]]

====Combining Materials====

If a balisong uses a combination of materials, for example in its handles, write a + between the materials.

TI+G10

====Or====

If you want to say that a balisong can use different materials, write a slash between the materials

G10/CF

====Live Blade VS Trainer====

Try to avoid creating separate entries into the Balisong list for live blades and trainers unless absolutely necessary.
If the live and trainer versions of a balisong differ in weight, material or other properties, use a semicolon (;) to separate the information within the same entry, but always list the live blade information first.

AEB-L;410

==Naming Conventions==

These naming conventions have been created to make page names more consistent, make it easiert for users to find pages and and to make linking easier.<br>
These rules apply to page titles, headings and file names, although headings follow a slightly looser version of these rules.

- Every word must be capitalized, even small words like "of" or "and", unless a name is intentionally written in lowecase, for example "iPhone".

- Always use singular instead of plural. For example "Washer" instead of "Washers".

- Use nouns, not verbs. Instead of "Tuning", use "Tune". A good rule of thumb for this is "Name the thing, not the action".

- Avoid unnecessary words. For example "Zen Pin" instead of "About The Zen Pin Mechanism"

==Creating a new Page==

Before you create a new article, please check whether that article already exists or not. The search bar at the top can be a good tool for that.

If you have made sure that the page you want to create doesnt already exist, you can create the article by opening the base link of this wiki (balisong.info) and append a forward slash (/) and append the name of the article you want to create. For example if you want to create an article called Banana, you would open this link:

http://balisong.info/Banana

After that you have to decide if you want to use the visual editor (not recommended), or the source editor. If you want to use the visual editor, click on "Create". If you want to use the source editor, click on "Create source". The next steps are almost identical with just editing an article, so please read the next section.

==Editing an article==

If you want to edit an article, you need to click on the "Edit" or "Edit Source" button. They are usually somewhere on the top right of your screen.

===Source Editor===

If you have clicked the "Edit source" button, a big box will appear in which you can write everything that you know about the topic of the article. If you want to see the changes to the article, scroll to the bottom of the page and click on the "Show preview" button. This will reload the article and show you the text with all the rendered Wikitext code that you have written.
After you have filled the article with information, scroll to the bottom of the page, and write a summary in the "Summary" block like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save page". You might also need to fill out an easy captcha for the changes to to live.

===Visual Editor===

The visual editor is not recommended since it has not been tested.

If you have clicked the "Edit" button you can just start writing down everything you know about the topic of the article.
After you have filled the article with information, click the "Save" button, add a summary message like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save Page". You might also need to fill out an easy captcha for the changes to to live.

===Objective Viewpoint===

When writing or editing articles, keep a neutral point of view. Just because you dislike a certaint product, doesn't mean it's objectively bad.

===Do Not Repeat Yourself===

If you want to add something to the wiki that has already been described on a different article, just link to it instead of repeating information that is already on the Balisong Wiki. See [[#Linking]] for a reminder on how to properly link to different articles and chapters.

===Similar Style===

If you are editing an article, check if there are other articles about similar topics and try to mimic that style.

For example if you want to write an article about a balisong, check out the article about the [[MachineWise_Slift_V2]] and try to copy the style that was used there.

==File Uploads==

The Balisong Wiki supports uploading of media. If you want to upload a picture, click on the "Upload file" field, or just click this link: [[Special:Upload]].<br>
Please check out [[#Naming_Conventions]] if you are unsure how to name your files.

===Only Submit Your Own Images===

Please only submit your own images as we do not want to get into trouble with copyright owners.

===Limits===

Please only upload files that are 1920x1080 or smaller. Large pictures take up a lot of ram, potentially making the Balisong Wiki go [https://en.wikipedia.org/wiki/Out_of_memory out of memory]. If you see a screen like this:
[[File:Out_Of_Memory.png]]
Please immediately contact the server owner [[Main_Page#Contact]].

The following sub-headings will containt important information on how to format images. If you want more information not covered in this editing guide, please check out the official Mediawiki guide for images [https://www.mediawiki.org/wiki/Help:Images https://www.mediawiki.org/wiki/Help:Images].

===Embedding===

Instructions for how to embed files on a page are on the file upload page [[Special:Upload]], but in case you want something clearer:<br>
If you want to embeda picture, write 2 brackets, then "File:" followed by the name of the file, including its file extension.
For example like this:

<nowiki>[[File:Slift_V2.png]]</nowiki>

===Stopping Floating Text===

Sometimes text will be rendered around the image which can look very awkward. To stop this from happening, simply add this line right after the image that you want to embed and leave an empty line after it:

<nowiki><div style="clear: both"></div></nowiki>

Which should look like this with the embed image added

<nowiki>[[File:Slift_V2.png]]</div>
<div style="clear: both">
</nowiki>

Or alternatively you use this code and replace the "..." with the embedding link of your image.

<nowiki><div style="overflow: hidden">…</div></nowiki>

With the embed added, it should look like this:

<nowiki><div style="overflow: hidden">[[File:Slift_V2.png]]</div></nowiki>

===Scaling===

====Resizing====

You can scale images by writing a pipe (|) and the ammount of pixels you want, after the embed.

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

====Restrict Image Within Space====

If you need to fit an image within a certain space, you can restrict its height, width, or both. Keep in mind that the aspect ratio will always be preserved.

=====Restricting Image Width=====

If you want to restrict the width, write the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

This will create an image that is at most 200 pixels wide.

=====Restricting Image Height=====

If you want to restrict the height, write a "x", after that the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|x200px]]</nowiki>

This will create an image that is at most 200 pixels high.

=====Restricting Image Both=====

If you want to restrict both, the height and the width, you can use can write the width, followed by a "x", then the height, and at the end, "px"

<nowiki>[[File:Slift_V2.png|150x200px]]</nowiki>

This will create an image that is at most 150 pixels wide and at most 200 pixels high.

===Thumbnail===

You can enable thumbnailing by adding the "thumb" keyword. This will draw a rectangle around the image to visually separate it from the text.

<nowiki>[[File:MachineWise_Slift_V2.jpg|thumb]]</nowiki>

===Alignment===

You can align the picture by adding the location to where it should be aligned

<nowiki>[[File:MachineWise_Slift_V2.jpg|right]]</nowiki>

===Caption===

You can add a cpation, by writing it as the last argument.

<nowiki>[[File:MachineWise_Slift_V2.jpg|Rose Gold Slift V2]]</nowiki>

===Multiple Arguments===

You can use multiple arguments by just chaining them together with pipes (|)

<nowiki>[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">
</nowiki>

This will embed a picture of a [[MachineWise]] [[MachineWise_Slift_V2]] on this page, which will be scaled to 600 pixels, aligned to the center of the screen, have a caption with "Rose Gold Slift V2", will not have any text floating around it and it will look like this:

[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">

==Measurements==

All measurementes must be provided in metric with an optional measurement in imperial in parenthesis. You are allowed to break this rule if you are citing a source (see the next sub-heading [[#Only_submit_your_own_measurements]] for more information).

6.350mm (0.250in)

or just

6.350mm

The unit of measurement is not neccessary, but should still be added if there is enough space for it. If there is no unit after the number, assume Millimeters or Grams depending on context. For example:

6.350 (0.250)

===Only Submit Your Own Measurements===

While manifacturers may provide measurements for their products, they are often times inaccurate. For example: Squid Industries lists their [https://www.squidindustries.co/products/oversized-bushings?variant=44002598682796 Nautilus bushings] as having an [[Pivot_System#Outer_Diameter]] of 0.2482" +/- .0002 OD = 6.30428mm +/- 0.00508, yet [[Pivot_System#Bushing|Pivot_System#Bushings]] with an [[Pivot_System#Outer_Diameter]] of 6.350mm (0.25in) fit perfectly. Similarly, Nabalis markets their [https://nabalis.com/cdn/shop/files/VULP_0f6d9ff8-34ba-4c2b-8775-15e20801042f.jpg?v=1746763288&width=700 bushings as 7mm OD], but actual measurements show an [[Pivot_System#Outer_Diameter]] of 6.985mm.

Because such discrepancies are common, we ask that you only submit measurements that you have personally verified in real life with a measuring device.

===Decimal Places===

Please add as many decimal places for youre measurements, as you can. The standard should be 3 decimal places.

6.326mm

==Comments==

If you want to add text that is only visible when editing the Balisong Wiki, for example when you want to tell another editor why you have done what you did, you can write a comment like so:

<nowiki></nowiki>

==Speculative Articles==

If you are unsure about a specific topic, do not write about it. You are however allowed to leave chapters empty and only write about the parts of the topic you're certain about. For example, if you know a lot about the history of a particular balisong or have interesting trivia, but don't own the knife yourself and therefore can't provide measurements, it's completely acceptable to fill in the History or Trivia chapters, while leaving the Measurements chapter blank.

==Redacted==

Some users prefer not to be included on the Balisong Wiki. Please respect their wishes and avoid writing about them. If mentioning them is absolutely necessary, for example if they have created a balisong, refer to them as {[[Redacted]]} instead of their name, like this:

The balisong was created by <nowiki>{[[Redacted]]}</nowiki>.

For a full list of people who have requested to be excluded from the Balisong Wiki, please read [[Redacted]].

==AI Usage==

Please do not use any form of LLMs/AI to write articles, as they are prone to hallucinations.

==The [[Sandbox]]==

In the [[Sandbox]] you can make and revert edits freely to familiarize yourself with how to make changes to the BalisongWiki with no fear of messing something up.

Edit Guide

2026-05-03T17:44:06Z

DexyStorm: fix example for disabling markup

==The Rules==

Thank you for showing interest in contributing content to the Balisong Wiki!

Please read the [[Code Of Conduct]] before making any changes to the Balisong Wiki.

==Account Creation==

You do not need an account to edit the wiki, but please keep in mind that your current public IP address will be visible once you publish a change if you are not logged into an account.
An E-Mail address is not required, just your username and password. When creating a password, make sure to remember it well, as there is currently no automated way to reset it. If you need help recovering your account, please [[Main_Page#Contact|contact the owner]].

==Formatting==

===Disable markup===

Mediawiki uses a custom markup language known as Wikitext which is similar to Markdown. It allows users to format text, create links, build tables and structure content using plain text syntax.

If you want your text to not get formatted by Wikitext, you can write it between two nowiki tags. For example<br>

<nowiki><nowiki>[https://www.google.com/ https://www.google.com/]</nowiki></nowiki>

will look like this:<br>

<nowiki>[https://www.google.com/ https://www.google.com/]</nowiki>

instead of being a clickable link to Google like this:<br>

[https://www.google.com/ https://www.google.com/]

===Indentation===

If you want your text to be segregated because you want to draw extra attention to it, you can write that important text in a new line and insert a space before your text. Mediawiki will draw a rectangle around your text and change the font to make it stand out more.

Some very important and interesting text.

===Headings===

====Spacing====

Always leave one empty line before and after each heading, like this:

Text<br>
=New Heading=<br>
Text

====Heading Counter====

The Balisong Wiki supports automatic counting of the headings. There is no need to manually number them. Once you are done with editing an article, the heading numbers will automatically be applied.

====Creating Headings====

To create headings, write the text of the heading between = like this:<br>

<nowiki>=First Heading=</nowiki>

You can make Sub-Headings by increasing the number of =<br>

<nowiki>==Sub-Heading for first Heading==</nowiki>

<nowiki>===Sub-Sub-Heading for first Heading===</nowiki>

====Disable Table Of Contents====

Articles with many chapters will have an automatic table of contents on the top left of that article. To disable the table of contents, put this line as the very first line of the article on which you want to disable this feature

<nowiki>__NOTOC__ </nowiki>

===Dates===

Dates should be written in [https://en.wikipedia.org/wiki/ISO_8601 ISO 8601] standard form.

Here are some examples:<br>

2024-12-30

2022-06-01

2020-01-23

===Break===

If you want to write text in a new line, but do not want the extra empty line that comes with it, you can use the <nowiki><br></nowiki> tag at the end of your line, like this:

<nowiki>Text<br>
Text</nowiki>

And it will be rendered like this:

<nowiki>Text
Text</nowiki>

==Linking==

In order to create a link to a different article, or a different website, you will need to use square brackets

<nowiki>[]</nowiki>

===Spaces===

If an article you want to link to has spaces, for example the Balisong List, just use underscores for those spaces<br>

<nowiki>[[Balisong_List]]</nowiki>

And it will be rendered like this:

[[Balisong_List]]

===Internal===

If you want to link to another article within the Balisong Wiki, write the name of the article between two square brackets like this:

<nowiki>[[Sandbox]]</nowiki>

And it will be rendered like this:

[[Sandbox]]

====Specific section====



=====To another article=====

If you want to link to a specific section, write the name of the article, then a pound symbol (#) then the name of the section.

<nowiki>[[Pin_System#Screw_Zen]]</nowiki>

And it will be rendered like this:

[[Pin_System#Screw_Zen]]

=====To the same article=====

If you want to link to a same section of the article that you are currently editing, you can leave the linking of the article part out, and just write the pund symbol (#) with the name of the section.<br>
This will link to the first section of this article<br>

<nowiki>[[#Account_creation]]</nowiki>

And it will be rendered like this:

[[#Account_creation]]

===Pipe===

Adding a pipe symbol (|) to the end of your internal linking enables you to write a custom name for the linking. This can be useful to slightly adjust the name of the link so that sentences flow better, or to remove the underscore that is caused by linking

<nowiki>[[Balisong_list|Balisong List]]</nowiki>

Will be rendered as

[[Balisong_list|Balisong List]]

Note: When linking to a chapter, please try to keep the original formating of the link (for example [[#Pipe]] instead of using a custom name, If you must use a custom name, at the very least, include the pund (#) in the link to indicate that it leads to a specific chapter. This helps readers recognize that the link points to a section they might have already seen.

===External===

If you want to link to a different website, for example to show the reader where they can buy a specific bushing, put your link in only 1 set of square brackets

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp]

If you want to give your link a name, add a space after the link and add a name.

<nowiki>[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.35mm OD bushings]</nowiki>

And it will be rendered like this:

[https://thetruelink.com/products/250-od-x-188-id-bushing-xp 6.35mm OD bushings]

==Tables==

Tables can be either edited by hand (not recommended), or a table generator can be used. We recommend this [https://www.tablesgenerator.com/mediawiki_tables# table generator].
If you wish to edit this table, copy it, go to the mentioned website, select "MediaWiki" which should be in the bar located at the very top of the page. After that, click "File" in the top left, click "Paste table data..." and paste it in. Wait a couple of seconds and then click the blue "Load" button. After that feel free to make any changes you deem neccessary. After you've adjusted the table, scroll all the way down and click on "Generate" button which is on the left hand side of the screen and wait a couple of seconds as generating a big table can take some time, especially if your device is slow. After that click on the green "Copy to clipboard" button which is on the right hand side of your screen, or just copy the whole code which is in the window right under the gray "'''Result''' (click "Generate" to refresh)" text. After that, delete the old table from this wiki and paste in your newly edited table.

===Formatting The Balisong List===

====Order====

If the list does not have a specific order, like the [[Balisong_List]], please list the entries in alphabetical order.

====Connecting Cells====

If you want to connect cells, please use the [https://www.tablesgenerator.com/mediawiki_tables# table generator]. Select all the cells that you want to connect by dragging your cursor over them. The cells should now have a yellow background. Now click the black button that has two arrows pointing to each other. The button should be at the top of your screen and should look like this:

[[File:Merge_Cells_Button.png]]

====Combining Materials====

If a balisong uses a combination of materials, for example in its handles, write a + between the materials.

TI+G10

====Or====

If you want to say that a balisong can use different materials, write a slash between the materials

G10/CF

====Live Blade VS Trainer====

Try to avoid creating separate entries into the Balisong list for live blades and trainers unless absolutely necessary.
If the live and trainer versions of a balisong differ in weight, material or other properties, use a semicolon (;) to separate the information within the same entry, but always list the live blade information first.

AEB-L;410

==Naming Conventions==

These naming conventions have been created to make page names more consistent, make it easiert for users to find pages and and to make linking easier.<br>
These rules apply to page titles, headings and file names, although headings follow a slightly looser version of these rules.

- Every word must be capitalized, even small words like "of" or "and", unless a name is intentionally written in lowecase, for example "iPhone".

- Always use singular instead of plural. For example "Washer" instead of "Washers".

- Use nouns, not verbs. Instead of "Tuning", use "Tune". A good rule of thumb for this is "Name the thing, not the action".

- Avoid unnecessary words. For example "Zen Pin" instead of "About The Zen Pin Mechanism"

==Creating a new Page==

Before you create a new article, please check whether that article already exists or not. The search bar at the top can be a good tool for that.

If you have made sure that the page you want to create doesnt already exist, you can create the article by opening the base link of this wiki (balisong.info) and append a forward slash (/) and append the name of the article you want to create. For example if you want to create an article called Banana, you would open this link:

http://balisong.info/Banana

After that you have to decide if you want to use the visual editor (not recommended), or the source editor. If you want to use the visual editor, click on "Create". If you want to use the source editor, click on "Create source". The next steps are almost identical with just editing an article, so please read the next section.

==Editing an article==

If you want to edit an article, you need to click on the "Edit" or "Edit Source" button. They are usually somewhere on the top right of your screen.

===Source Editor===

If you have clicked the "Edit source" button, a big box will appear in which you can write everything that you know about the topic of the article. If you want to see the changes to the article, scroll to the bottom of the page and click on the "Show preview" button. This will reload the article and show you the text with all the rendered Wikitext code that you have written.
After you have filled the article with information, scroll to the bottom of the page, and write a summary in the "Summary" block like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save page". You might also need to fill out an easy captcha for the changes to to live.

===Visual Editor===

The visual editor is not recommended since it has not been tested.

If you have clicked the "Edit" button you can just start writing down everything you know about the topic of the article.
After you have filled the article with information, click the "Save" button, add a summary message like "First edit of the Banana page" or "Fixed typo in the #Zen_Pin section" and click on "Save Page". You might also need to fill out an easy captcha for the changes to to live.

===Objective Viewpoint===

When writing or editing articles, keep a neutral point of view. Just because you dislike a certaint product, doesn't mean it's objectively bad.

===Do Not Repeat Yourself===

If you want to add something to the wiki that has already been described on a different article, just link to it instead of repeating information that is already on the Balisong Wiki. See [[#Linking]] for a reminder on how to properly link to different articles and chapters.

===Similar Style===

If you are editing an article, check if there are other articles about similar topics and try to mimic that style.

For example if you want to write an article about a balisong, check out the article about the [[MachineWise_Slift_V2]] and try to copy the style that was used there.

==File Uploads==

The Balisong Wiki supports uploading of media. If you want to upload a picture, click on the "Upload file" field, or just click this link: [[Special:Upload]].<br>
Please check out [[#Naming_Conventions]] if you are unsure how to name your files.

===Only Submit Your Own Images===

Please only submit your own images as we do not want to get into trouble with copyright owners.

===Limits===

Please only upload files that are 1920x1080 or smaller. Large pictures take up a lot of ram, potentially making the Balisong Wiki go [https://en.wikipedia.org/wiki/Out_of_memory out of memory]. If you see a screen like this:
[[File:Out_Of_Memory.png]]
Please immediately contact the server owner [[Main_Page#Contact]].

The following sub-headings will containt important information on how to format images. If you want more information not covered in this editing guide, please check out the official Mediawiki guide for images [https://www.mediawiki.org/wiki/Help:Images https://www.mediawiki.org/wiki/Help:Images].

===Embedding===

Instructions for how to embed files on a page are on the file upload page [[Special:Upload]], but in case you want something clearer:<br>
If you want to embeda picture, write 2 brackets, then "File:" followed by the name of the file, including its file extension.
For example like this:

<nowiki>[[File:Slift_V2.png]]</nowiki>

===Stopping Floating Text===

Sometimes text will be rendered around the image which can look very awkward. To stop this from happening, simply add this line right after the image that you want to embed and leave an empty line after it:

<nowiki><div style="clear: both"></div></nowiki>

Which should look like this with the embed image added

<nowiki>[[File:Slift_V2.png]]</div>
<div style="clear: both">
</nowiki>

Or alternatively you use this code and replace the "..." with the embedding link of your image.

<nowiki><div style="overflow: hidden">…</div></nowiki>

With the embed added, it should look like this:

<nowiki><div style="overflow: hidden">[[File:Slift_V2.png]]</div></nowiki>

===Scaling===

====Resizing====

You can scale images by writing a pipe (|) and the ammount of pixels you want, after the embed.

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

====Restrict Image Within Space====

If you need to fit an image within a certain space, you can restrict its height, width, or both. Keep in mind that the aspect ratio will always be preserved.

=====Restricting Image Width=====

If you want to restrict the width, write the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|200px]]</nowiki>

This will create an image that is at most 200 pixels wide.

=====Restricting Image Height=====

If you want to restrict the height, write a "x", after that the length of the pixels how long the image at most can be, followed by "px".

<nowiki>[[File:Slift_V2.png|x200px]]</nowiki>

This will create an image that is at most 200 pixels high.

=====Restricting Image Both=====

If you want to restrict both, the height and the width, you can use can write the width, followed by a "x", then the height, and at the end, "px"

<nowiki>[[File:Slift_V2.png|150x200px]]</nowiki>

This will create an image that is at most 150 pixels wide and at most 200 pixels high.

===Thumbnail===

You can enable thumbnailing by adding the "thumb" keyword. This will draw a rectangle around the image to visually separate it from the text.

<nowiki>[[File:MachineWise_Slift_V2.jpg|thumb]]</nowiki>

===Alignment===

You can align the picture by adding the location to where it should be aligned

<nowiki>[[File:MachineWise_Slift_V2.jpg|right]]</nowiki>

===Caption===

You can add a cpation, by writing it as the last argument.

<nowiki>[[File:MachineWise_Slift_V2.jpg|Rose Gold Slift V2]]</nowiki>

===Multiple Arguments===

You can use multiple arguments by just chaining them together with pipes (|)

<nowiki>[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">
</nowiki>

This will embed a picture of a [[MachineWise]] [[MachineWise_Slift_V2]] on this page, which will be scaled to 600 pixels, aligned to the center of the screen, have a caption with "Rose Gold Slift V2", will not have any text floating around it and it will look like this:

[[File:MachineWise_Slift_V2.jpg|600px|thumb|center|Rose Gold Slift V2]]
<div style="clear: both">

==Measurements==

All measurementes must be provided in metric with an optional measurement in imperial in parenthesis. You are allowed to break this rule if you are citing a source (see the next sub-heading [[#Only_submit_your_own_measurements]] for more information).

6.350mm (0.250in)

or just

6.350mm

The unit of measurement is not neccessary, but should still be added if there is enough space for it. If there is no unit after the number, assume Millimeters or Grams depending on context. For example:

6.350 (0.250)

===Only Submit Your Own Measurements===

While manifacturers may provide measurements for their products, they are often times inaccurate. For example: Squid Industries lists their [https://www.squidindustries.co/products/oversized-bushings?variant=44002598682796 Nautilus bushings] as having an [[Pivot_System#Outer_Diameter]] of 0.2482" +/- .0002 OD = 6.30428mm +/- 0.00508, yet [[Pivot_System#Bushing|Pivot_System#Bushings]] with an [[Pivot_System#Outer_Diameter]] of 6.350mm (0.25in) fit perfectly. Similarly, Nabalis markets their [https://nabalis.com/cdn/shop/files/VULP_0f6d9ff8-34ba-4c2b-8775-15e20801042f.jpg?v=1746763288&width=700 bushings as 7mm OD], but actual measurements show an [[Pivot_System#Outer_Diameter]] of 6.985mm.

Because such discrepancies are common, we ask that you only submit measurements that you have personally verified in real life with a measuring device.

===Decimal Places===

Please add as many decimal places for youre measurements, as you can. The standard should be 3 decimal places.

6.326mm

==Comments==

If you want to add text that is only visible when editing the Balisong Wiki, for example when you want to tell another editor why you have done what you did, you can write a comment like so:

<nowiki></nowiki>

==Speculative Articles==

If you are unsure about a specific topic, do not write about it. You are however allowed to leave chapters empty and only write about the parts of the topic you're certain about. For example, if you know a lot about the history of a particular balisong or have interesting trivia, but don't own the knife yourself and therefore can't provide measurements, it's completely acceptable to fill in the History or Trivia chapters, while leaving the Measurements chapter blank.

==Redacted==

Some users prefer not to be included on the Balisong Wiki. Please respect their wishes and avoid writing about them. If mentioning them is absolutely necessary, for example if they have created a balisong, refer to them as {[[Redacted]]} instead of their name, like this:

The balisong was created by <nowiki>{[[Redacted]]}</nowiki>.

For a full list of people who have requested to be excluded from the Balisong Wiki, please read [[Redacted]].

==AI Usage==

Please do not use any form of LLMs/AI to write articles, as they are prone to hallucinations.

==The [[Sandbox]]==

In the [[Sandbox]] you can make and revert edits freely to familiarize yourself with how to make changes to the BalisongWiki with no fear of messing something up.

Pin System

2026-05-03T17:29:29Z

DexyStorm: when cranking zen screws, the bushings or washers are not always at fault. sometimes the zen pin presses into the liners, making the space between liner and blade thinner

Pin Systems are used to keep the blade from hitting the inside of the the handles and to keep the handles from hitting each other. The latter is called [[slap]].<br>

==Material Hardness==

To understand the pros and cons of every pin system, it's important to first learn about material hardness.

There are many different scales on which hardness can be measured, but the most widely-used for steel is the [https://en.wikipedia.org/wiki/Rockwell_hardness_test Rockwell Hardness scale C]. It is often abbreviated to HRC.

Properly heat-treated steel typically falls in the 59-68HRC range, depending on the steel.<br>
Non-heat-treated steel is generally around 35-41HRC.<br>
Titanium usually has a hardness of about 36-38HRC.

The higher the HRC number, the harder the material. Harder materials are more brittle, which means they are more prone to snapping, cracking or shattering. Softer materials (lower HRC) are more malleable and deform under stress rather than breaking. For example: The handles of the [[Nabalis_Canyon|Canyon]] are very thin and are made out of heat-treated stainless steel. Some users have reported that their handles have snapped after drops. Meanwhile, the [[MachineWise_Slift_V2|Slift V2]] also has very thin handles, but they are made of titanium. Rather than snapping, titanium will generally just deform because of its lower hardness.

If two materials that both have a high HRC hit against each other, one, if not both of those materials will be at risk of snapping, cracking or shattering.<br>
If two materials with different hardness ratings make contact, the softer one will always yield to the harder one, meaning that the softer material will get squised and deformed.
If two materials that both have a low HRC hit against each other, both of those materials with squish and deform each other, but the ammount is very small.

==Different Pin Systems==

There are currently three types of pin systems used in balisongs.<br>

===Zen Pin===

If the stopping mechanism is a stainless steel pin housed inside the handle, it is called a "zen pin" system. There are multiple implementations of zen pin systems, but they all have in common that a pin is inside the handle.

Zen pins can be found on both aluminium and titanium balisongs.

====Press-fit====

Press-fit Zen pins are typically only used in [[Construction#Channel|Channel]] balisongs, as this system depends on the structural rigidity that channel construction provides. A stainless steel pin is pressed into a hole which is slightly smaller than the pin itself, creating a tight [https://en.wikipedia.org/wiki/Interference_fit interference fit]. The pin is held in place by friction generated from the pin being slightly larger than the hole, ensuring it stays securely in place during use. An example of a balisong which uses this type of Pin system is the [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]].

====Glued====

Glued zen pins are usually only found on cheap balisongs. They function the same way as [[#Press-fit]] zen pins, with the only difference being that they are held in place with adhesive, rather than by friction. As a result, they tend to fall out much more easily. If a glued zen pin comes loose, it can usually be reinstalled using Loctite or another suitable adhesive.

====Screw Zen====

The screw zen system is only used in [[Construction#Channel]] or [[Construction#Sandwich]] construction knives. The screw zen pin system uses a [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=667aadb5d&_ss=r threaded shoulder pin], or just a [https://thetruelink.com/products/3-16-stainless-straight-pivot-6-64 threaded barrel]. Threaded shoulder pins are usually held in place by a small cutout in the handle in which the pin snaps into place, making the screws not necessarry for this type of construction to work. The problem with this type of Pin System is that over time the should pin will press into the handle, reducing the space between the handle and the blade. As a result, your balisong will bind if you crank the zen screws. You can temporarily fix this by using thinner [[Washer|washer]]s, not using zen pin screws or by using very oversized bushings. If the problem becomes too severe, only replacing the slab or liner will fix it. The barrels, however, are usually held in place by just the screws, meaning that no part of the barrel is pressing into the handle. An example for a balisong with a threaded shoulder pin is the [[Bladerunners_Systems_Replicant|Replicant]] and an example of a screw barrel system is the [[Henninger_Design_Telesto_v3|Telesto v3]].

The screw zen system is sometimes called "Tunable zen system", implying that it can be tuned. This is however misleading because if your balisong [[Bind|binds]] when tightening the zen screws, the issue usually never lies with the screws, but somewhere else. If you want to learn more about this, check out [[Pivot_System#Unexpected_Binding]].

====Hidden Zen====

Hidden zen pins can only be used if the balisong utilizes a construction method in which a piece of material sits above the zen pin. An example for a [[Construction#Sandwich|Sandwich]] construction knife with a hidden zen system is the [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]] an example for a [[Construction#Chanwich|Chanwich]] knife with a hidden zen system is the [[Squid_Industries_Tsunami|Tsunami]] and an example for a [[Construction#Channel|Channel]] knife with a hidden zen system is the [[Nabalis_Crescent|Crescent]].

====Shielded Zen====

Shielded Zen pins function the exact same way as [[#Hidden_Zen]] pins, except that they are only used on a channel knives. A small section which includes the section around the [[Pivot_Sexbolt]] is removed from the handle and a slot for the zen pin is machined into the handle, simmiliar to a [[#Press-fit]] setup. Once the zen pin is installed, the removed section is reattatched and held in place by the [[Pivot_Sexbolt]]. This pin system was invented by [[Jimpy]]. Here is a video demonstration: [https://www.instagram.com/p/CzzWaUkPGBy/ https://www.instagram.com/p/CzzWaUkPGBy/]

====Heat-treated vs Non-heat-treated Zen Pins====

Heat-treated zen pins run the risk of shattering, because the hard blade is hitting the hard zen pins, while non-heat-treated zen pins will gradually deform over time, making the handle gap smaller, as described in [[#Material_Hardness]]. An example for a balisong which utilizes heat treated zen pins, is the [[Bladerunners_Systems_Replicant|Replicant]]. An example for a balisong which utilizes non heat treated zen pins, is the [[Squid_Industries_Krake_Raken|Krake Raken]].

===Tang Pin===

Tang pins work very similarily to [[#Press-fit|press fit zen pins]]. The biggest difference is that two pins are pressed inside the blade. An example for this type of pin system is the [[Bladerunners_Systems_Alpha_Beast_3.0|Alpha Beast 3.0]].

While there are tang pin balisongs with aluminum handles, such as the [[Squid_Industries_Nautilus|Nautilus]], tang pins generally do not work well with aluminium. This is because the unhardened tang pin is still significantly harder than aluminium, causing the aluminium handles to deform over time. As a result, the handle gap will degrade, eventually leading to [[slap]]

====Heat Treated vs Non Heat Treated Tang Pins====

Tang pins must always be non heat treated, this is because the pin needs to conform to the shape of the hole in the blade during the press-fit process. If the tang was hardened, pressing it into the blade could cause the blade to crack due to the lack of give in both the blade, and the tang pin. Additionally, tang pins directly contact the soft titanium handles. By not heat-treating the tang pin, both materials should have similar hardness, allowing them to deform slightly and absorb impact without causing damange. If the pin were heat-treated, it would be significantly harder than the titanium, causing the titanium to deform and eventually leading to [[slap]].

===Pinsless===

The pinsless system attempts to achieve the same clean aesthetic as [[#Hidden Zen|hidden zen]] pins, but with a [[Construction#Channel|channel]] construction. Instead of using a zen pin, the area of the handle where the pin would normally be inserted is left unmachined. This uncut part of the handle acts acts as a built-in pin. An example of a knife with a pinsless design is the [[JK_Monarch|JK Monarch]]<br>

Due to the difference in hardness between the hardened blade and the soft titanium handles, this type of pin system (or lack thereof) will inevitably cause the handle gap to degrade over time, eventaully leading to [[slap]].

Pin System

2026-05-03T17:27:27Z

DexyStorm: fix 1 tang pin in blade -> 2 tang pins in blade

Pin Systems are used to keep the blade from hitting the inside of the the handles and to keep the handles from hitting each other. The latter is called [[slap]].<br>

==Material Hardness==

To understand the pros and cons of every pin system, it's important to first learn about material hardness.

There are many different scales on which hardness can be measured, but the most widely-used for steel is the [https://en.wikipedia.org/wiki/Rockwell_hardness_test Rockwell Hardness scale C]. It is often abbreviated to HRC.

Properly heat-treated steel typically falls in the 59-68HRC range, depending on the steel.<br>
Non-heat-treated steel is generally around 35-41HRC.<br>
Titanium usually has a hardness of about 36-38HRC.

The higher the HRC number, the harder the material. Harder materials are more brittle, which means they are more prone to snapping, cracking or shattering. Softer materials (lower HRC) are more malleable and deform under stress rather than breaking. For example: The handles of the [[Nabalis_Canyon|Canyon]] are very thin and are made out of heat-treated stainless steel. Some users have reported that their handles have snapped after drops. Meanwhile, the [[MachineWise_Slift_V2|Slift V2]] also has very thin handles, but they are made of titanium. Rather than snapping, titanium will generally just deform because of its lower hardness.

If two materials that both have a high HRC hit against each other, one, if not both of those materials will be at risk of snapping, cracking or shattering.<br>
If two materials with different hardness ratings make contact, the softer one will always yield to the harder one, meaning that the softer material will get squised and deformed.
If two materials that both have a low HRC hit against each other, both of those materials with squish and deform each other, but the ammount is very small.

==Different Pin Systems==

There are currently three types of pin systems used in balisongs.<br>

===Zen Pin===

If the stopping mechanism is a stainless steel pin housed inside the handle, it is called a "zen pin" system. There are multiple implementations of zen pin systems, but they all have in common that a pin is inside the handle.

Zen pins can be found on both aluminium and titanium balisongs.

====Press-fit====

Press-fit Zen pins are typically only used in [[Construction#Channel|Channel]] balisongs, as this system depends on the structural rigidity that channel construction provides. A stainless steel pin is pressed into a hole which is slightly smaller than the pin itself, creating a tight [https://en.wikipedia.org/wiki/Interference_fit interference fit]. The pin is held in place by friction generated from the pin being slightly larger than the hole, ensuring it stays securely in place during use. An example of a balisong which uses this type of Pin system is the [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]].

====Glued====

Glued zen pins are usually only found on cheap balisongs. They function the same way as [[#Press-fit]] zen pins, with the only difference being that they are held in place with adhesive, rather than by friction. As a result, they tend to fall out much more easily. If a glued zen pin comes loose, it can usually be reinstalled using Loctite or another suitable adhesive.

====Screw Zen====

The screw zen system is only used in [[Construction#Channel]] or [[Construction#Sandwich]] construction knives. The screw zen pin system uses a [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=667aadb5d&_ss=r threaded shoulder pin], or just a [https://thetruelink.com/products/3-16-stainless-straight-pivot-6-64 threaded barrel]. Threaded shoulder pins are usually held in place by a small cutout in the handle in which the pin snaps into place, making the screws not necessarry for this type of construction to work. The problem with this type of Pin System is that over time the should pin will press into the handle, reducing the space between the handle and the blade. As a result, your balisong will bind if you crank the zen screws. You can temporarily fix this by using thinner [[Washer|washer]]s, not using zen pin screws or by using very oversized bushings. If the problem becomes too severe, only replacing the slab or liner will fix it. The barrels, however, are usually held in place by just the screws, meaning that no part of the barrel is pressing into the handle. An example for a balisong with a threaded shoulder pin is the [[Bladerunners_Systems_Replicant|Replicant]] and an example of a screw barrel system is the [[Henninger_Design_Telesto_v3|Telesto v3]].

The screw zen system is sometimes called "Tunable zen system", implying that it can be tuned. This is however misleading because if your balisong [[Bind|binds]] when tightening the zen screws, the issue usually never lies with the screws, but with the [[Bushing|bushings]], or [[Washer|washers]]. If you want to learn more about this, check out [[Pivot_System#Unexpected_Binding]].

====Hidden Zen====

Hidden zen pins can only be used if the balisong utilizes a construction method in which a piece of material sits above the zen pin. An example for a [[Construction#Sandwich|Sandwich]] construction knife with a hidden zen system is the [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]] an example for a [[Construction#Chanwich|Chanwich]] knife with a hidden zen system is the [[Squid_Industries_Tsunami|Tsunami]] and an example for a [[Construction#Channel|Channel]] knife with a hidden zen system is the [[Nabalis_Crescent|Crescent]].

====Shielded Zen====

Shielded Zen pins function the exact same way as [[#Hidden_Zen]] pins, except that they are only used on a channel knives. A small section which includes the section around the [[Pivot_Sexbolt]] is removed from the handle and a slot for the zen pin is machined into the handle, simmiliar to a [[#Press-fit]] setup. Once the zen pin is installed, the removed section is reattatched and held in place by the [[Pivot_Sexbolt]]. This pin system was invented by [[Jimpy]]. Here is a video demonstration: [https://www.instagram.com/p/CzzWaUkPGBy/ https://www.instagram.com/p/CzzWaUkPGBy/]

====Heat-treated vs Non-heat-treated Zen Pins====

Heat-treated zen pins run the risk of shattering, because the hard blade is hitting the hard zen pins, while non-heat-treated zen pins will gradually deform over time, making the handle gap smaller, as described in [[#Material_Hardness]]. An example for a balisong which utilizes heat treated zen pins, is the [[Bladerunners_Systems_Replicant|Replicant]]. An example for a balisong which utilizes non heat treated zen pins, is the [[Squid_Industries_Krake_Raken|Krake Raken]].

===Tang Pin===

Tang pins work very similarily to [[#Press-fit|press fit zen pins]]. The biggest difference is that two pins are pressed inside the blade. An example for this type of pin system is the [[Bladerunners_Systems_Alpha_Beast_3.0|Alpha Beast 3.0]].

While there are tang pin balisongs with aluminum handles, such as the [[Squid_Industries_Nautilus|Nautilus]], tang pins generally do not work well with aluminium. This is because the unhardened tang pin is still significantly harder than aluminium, causing the aluminium handles to deform over time. As a result, the handle gap will degrade, eventually leading to [[slap]]

====Heat Treated vs Non Heat Treated Tang Pins====

Tang pins must always be non heat treated, this is because the pin needs to conform to the shape of the hole in the blade during the press-fit process. If the tang was hardened, pressing it into the blade could cause the blade to crack due to the lack of give in both the blade, and the tang pin. Additionally, tang pins directly contact the soft titanium handles. By not heat-treating the tang pin, both materials should have similar hardness, allowing them to deform slightly and absorb impact without causing damange. If the pin were heat-treated, it would be significantly harder than the titanium, causing the titanium to deform and eventually leading to [[slap]].

===Pinsless===

The pinsless system attempts to achieve the same clean aesthetic as [[#Hidden Zen|hidden zen]] pins, but with a [[Construction#Channel|channel]] construction. Instead of using a zen pin, the area of the handle where the pin would normally be inserted is left unmachined. This uncut part of the handle acts acts as a built-in pin. An example of a knife with a pinsless design is the [[JK_Monarch|JK Monarch]]<br>

Due to the difference in hardness between the hardened blade and the soft titanium handles, this type of pin system (or lack thereof) will inevitably cause the handle gap to degrade over time, eventaully leading to [[slap]].

Pivot System

2026-05-02T10:35:01Z

DexyStorm: reordered bushing measurements to be alphabetical

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: height, inner diameter and outer diameter.

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Tune#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washers=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Pivot System

2026-05-02T07:03:47Z

DexyStorm: add video of visual demonstration on how the bushing system works

The pivot system of a balisong determins how the handles rotate around the blade. There are currently four types of pivot systems.

==[[Washer]]==

The [[washer]] pivot system, often referred to as "washer only", uses only [[washer|washers]] between the blade and handles. While other systems may include washers as part of a more complex setup (like [[#Bushing|bushing]]s), a [[washer]] only system relies solely on the washers.

In this system, the blade is sandwiched between two [[washer]]s, which are usually made out of phosphor bronze. This washer-blade-washer assembly is then clamped between the two handle halves. A sexbolt goes through the entire stack: handle-washer-blade-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade.

===Tuning Washers===

Tuning a [[washer]] balisong is done by adjusting the tightness of the pivot screws. The torque applied to the screws determines how freely the handles rotate. If the screws are too tight, the balisong will bind. If the screws are too loose, the balisong will feel losse and might even tap. After screwing the pivot screws in, [[#Feel|check the tolerances]] and adjust the screws accordingly.

Because a proper tune relies on not fully tightening the screws, you will not get full thread friction retention. This means that the screws are more likely to loosen over time as compared to a [[#Bushing|bushing]] system. To prevent this, some form of threadlocker is typically used.

===Assembling [[washer]] Only===

When you are disassembling an already assembled [[washer]] only balisong, make sure to note the orientation of each [[washer]] and reassemble everything exactly as it was. There is an exception: Sometimes phosphor bronze washers come with a smooth/rounded and a rough/blocky side. The smooth side should always face the blade to ensure a smooth swing and prevent binding. Some manifacturers overlook this detail and install the washers incorrectly. In that case you should flip the [[washer]] so the smooth side faces the blade.

==Bushing==

[[File:Bali cross section labeled.png|700px|thumb|right|Bushing Balisong Cross section]]

A bushing is a small cylinder, usually made out of heat-treated stainless steel.

The bushing pivot system is sometimes also called "traditional bushing system" or "normal bushing system" because there is another pivot system that uses bushings, the [[Floating_Washer|floating washer]] system. However, since the traditional bushing system is by far the most common pivot system, people will assume you're reffering to traditional bushings, when you meantion "bushing".

In a traditional bushing system, the bushing goes inside the [[blade]]'s pivot hole and gets sandwiched by two [[Washer|washers]] on each side. This washer-bushing(which is inside the blade)-washer assembly is then clamped between the two handle halves. A sexbolt passes through the entire stack: handle-washer-bushing(which is inside the blade)-washer-handle, to keep it from fallig apart. A pivot screw is screwed in from the other side to keep the sexbolt from falling out. At this point, the sexbolt, washers, bushing, handles and screw function as a single, solid unit, meaning they move together without any friction between them. The blade acts as a second independent component, meaning it is allowed to freely swing around the handles. The only friction in this systems is between the washers and the blade and between the outer diameter of the bushing and the blade as the bushing "scrapes" against the insides of the bushing holes of the blade. For a visual demonstration, watch this video: [https://www.youtube.com/watch?v=cRuyf2VN92A https://www.youtube.com/watch?v=cRuyf2VN92A].

===Sizes===

Bushings have 3 measurements: [[Outer_Diameter|outer diameter]], [[Inner_Diameter|inner diameter]], and [[Height|height]].

====Inner Diameter====

Often abbreviated to ID.<br>
The ID of most bushings will usually be the same, around 4.7mm-4.8mm (0.188in)

====Outer Diameter====

Often abbreviated to OD.<br>
Unfortunately there is no standard for bushing sizes. Some balisongs may use the same bushing size, but this is not guaranteed. For example:<br>
[[Bladerunners_Systems|Bladerunners Systems]] uses 6.350mm for their [[Bladerunners_Systems_Replicant|Replicant]]<br>
[[Nabalis]] uses 6.985mm for their [[Nabalis_Vulp|Vulp]]<br>
[[Baliplus]] uses 7.052mm for their [[Baliplus_Titanium_Barebones|Titanium Barebones]] clone.<br>
[[Squid_Industries|Squid Industries]] uses 6.304mm for their [[Squid_Industries_Nautilus|Nautilus]] and [[Squid_Industries_Krake_Raken_V3|Krake Raken]], even though 6.350mm fits just fine.<br>
[[Baliplus]] uses 6.299mm for their [[Baliplus_Serif|Serif]] clone.<br>
To see a list of which balisongs use which type of bushing, check out the [[Balisong_list|balisong list]].<br>

While some of those differences may looks small (for example: 6.985 vs 7.052), they can still dictate whether a bushing might or might not fit inside the bushing hole of a [[blade]]. You can use a smaller bushing for a larger bushing hole (for example 6.985 inside a blade that needs 7.052) but that will introduce problems described in [[Tune#Handles Move Forwards And Backwards]].

====Length====

The last axis of the bushing is the length. It is the only flat part of the bushing.

===Assembling Bushings===

When you are disassembling an already assembled bushing balisong, make sure to note the orientation of each bushing and washer. Reassemble everything exactly as it was. That means inserting each bushing into the same side of the blade using the same [[washer]] on the same side as before. That is because once a [[washer]] has been pressed against a bushing, the bushing will press a small groove into the washer, forming a bond, which means that the [[washer]] should only ever be re-used with that specific bushing with the same [[washer]] side facing the same bushing side. This is sometimes called "marrying".

Please also read [[#Assembling_Washer_Only]] as everything that has been written down there, also applies to bushing balisongs.

===Bushing Tuning===

One of the main advantages of a traditional bushing system is that, when set up correctly, allows for a perfect tune: no tap, no play and completely free-swinging handles with no bind.

Tuning a traditional bushing system involves adjusting the length of the bushings, typically by sanding, untill it is only slightly longer than the thickness of the blade. If the bushing is too long, the blade will have too much side-to-side movement between the handles and in extreme cases, the blade will hit the handles and it will [[tap]]. If the bushing is too short, you will have [[Bind|bind]] because at that point, the bushing becomes useless and the balisong will behave as if it was running on a [[#Washer|washer-only]] system.

The optimal length for the bushing varies between balisong to balisong, blade to blade and even pivot hole to pivot hole (so never mix your bushings and always keep track of which bushing you have tuned for what pivot of what blade), but the optimal length is somewhere about 0.025mm (0.001in) longer than the blade. A good starting point is 0.030mm and then go from there. You must also be careful to not sand your bushing at an angle because this will make your balisong bind, but only in specific handle positions. Some community members tend to call uneven bushings "lopsided". There are measures and tools to counteract an uneven bushing. These measures and tools will get discussed in the [[#Lapping_Methods]] chapter.

====Lapping Surface====

You will need some surface on which you can lap your bushings.

=====Sand Paper=====

Most people use sandpaper. While sandpaper usually works just fine, it usually comes warped/curled, so you run the risk of making your bushing uneven because the side of the bushing which is closer tho the warped part of the sandpaper, will automatically have more pressure applied to it, making your bushing uneven. So if you want to use sandpaper, make sure to properly straighten it out before you start lapping your bushings. This can be done by bending the sandpaper in the other direction and/or by taping it down to a straight and sturdy surface. You will also need a hard, flat surface underneath the sandpaper, like a slab of marble. A wooden desk or countertop is not hard enough.

=====Sharpening Stone=====

Resin bonded diamond sharpening stones can be used as a premium and longer lasting lapping surface compared to [[#Sand_Paper|#Sand Paper]]. They allow for more security against uneven bushings and more consistent lapping since they get worn out a lot slower.

Stay away from cheap sharpening stones like those shown in this video: [https://www.youtube.com/watch?v=V5shv-7m5Ic https://www.youtube.com/watch?v=V5shv-7m5Ic], as they tend to develop a recess in the center over time which will make your bushings uneven. They also come with a range of other problems covered in the video.

Here is a decent sharpening stone:

Amazon DE: [https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1 https://www.amazon.de/dp/B07GRWN1PV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1]

Amazon US: [https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV https://www.amazon.com/SHARPAL-Diamond-Whetstone-Storage-Sharpening/dp/B07GRWN1PV]

=====Grit=====

While you can successfully lap a bushing with only one grit size, at least two grit sizes are recommended: a coarse and a fine grit. Something like 325 and 1200 grit work just fine. You should use the low grit when you are far off your target bushing length, and the high grit when you are close, so that you do not accidentally overshoot your target and end up with an undersized bushing.

=====Strop=====

Regardless of whether you are using sandpaper or sharpening stones, you should also invest in a strop. Stropping helps reduce any [[bur]] that may form on the edges of the bushing during lapping and removes residue stuck to the surface. This results in a smoother, more consistent bushing surface.

Amazon DE: [https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X https://www.amazon.de/-/en/SHARPAL-204N-Leather-Polishing-Sharpening/dp/B09KV5D79X]

Amazon US: [https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1 https://www.amazon.com/SHARPAL-204N-Polishing-Sharpening-Woodcarving/dp/B07WC1M411?th=1]

You will probably also want to apply some stropping compound on your strop before using it.

Stroppystuff is a well-regarded brand for stropping compound, though the price reflects that. [https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml https://stroppystuff.com/products/6-micron-mono-diamond-suspension-high-concentration-30ml]

Avoid chromium oxide oxide compounds, as they are not suitable for high-hardness stainless steels.

For more information on strops, watch this video: [https://www.youtube.com/watch?v=pMnS1jU4904 https://www.youtube.com/watch?v=pMnS1jU4904]. Even though it focuses on knife sharpening, much of it also applies to bushings.

====Lapping Methods====

There are different lapping methods depending on the tools you have.

Always lap only one side of the bushing. This keeps the bushing as flat as possible and makes it easier to fix the bushing if it becomes uneven.

Uneven bushings are extremely common, as factories usually dont sell perfectly flat bushings and all lapping methods will introduce some degree of unevenness. For a guide on how to minimize the risk of and fix uneven bushings, read [[#Uneven_Bushing]].

=====By Hand=====

If you have no lapping tools, you will have to lap the bushing by hand. Start by placing your bushing flat-side-down on your lapping surface and lap the bushing in a circular or figure-eight motion while applying even and constant pressure across the whole bushing. After a few motions, usually between 3 and 10 (in this example we will use 5), '''but always keep the number of motions the same''', rotate the bushing 90 degrees. Repeat this process three more times. In total you should have performed 4 rotations (ending back at your original position) and 20 circles or figure-eights (5 per rotation). This completes one pass.

After you have completed one pass, you should [[#Strop]] the bushing. Use the exact same technique as described above, but with stropping, you do not have to follow the steps as precisely because stropping removes little to no material. After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[KnifeDogs Pivot Lap]]=====

The KnifeDogs pivot lap includes one puck, multiple adapters and multiple plungers. Every plunger fits exactly one adapter perfectly.

To begin, you first need to figure out which adapter fits your bushing. Start by try placing your bushing insde one of the the adapters. If the adapter hole is too small, try one one with a larger hole. If the bushing is loose inisde the adapter, pick an adapter with a smaller hole. If your bushing fits perfectly inside the adapter with little to no wiggle, you have the correct adapter. Next, you need to find the correct plunger. Use the same process as before, but instead of putting the bushing into the adapter, you need to try putting the plunger into the adapter.

After you have found the correct adapter and plunger, place the puck on worn out 600-800 grit sand paper with the logo/text "KNIFEDOGS PIVOT LAP" facing toward you. It is very important that your sandpaper is already very worn out, as wearing the sandpaper out will create a much more even surface which will make producing even bushings much easier. Insert the adapter into the puck and place your bushing inside the adapter with the side that you want to sand, facing downward. Next, insert the plunger into the adapter so it sits on top of the bushing.

After that, press down on the plunger very lightly and on the puck VERY firmly (almost as hard as you can) and move the entire assembly in circles or figure eights across your worn out lapping surface. Use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The lighter you press down on the plunger and the more pressure you put on the puck, the more even your bushing will be. When you have just purchased the pivot lap, the adapter will have a small lip that will hold the bushing inside the adapter. This lip will gradually wear down with use, so be careful not to drop or lose the bushing when lifting up the pivot lap. After you have done a couple of circles or figure-eights, [[#Strop]] the bushing.

Do not strop your bushing with the pivot lap as this will damage the strop. Always strop the bushing by hand with the stropping technique described near the end in the [[#By Hand]] chapter.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

=====[[Nabalis_Bushing_Buddy|Nabalis Bushing Buddy]]=====

Using a Bushing Buddy is by far the worst lapping method. Read its shortcomings and critique here: [[Nabalis_Bushing_Buddy#Critique]]

Place a white (soft) or black (hard) rubber ball inside the groove in the middle of the Bushing Buddy body and slide the sandpaper through the hat of the Bushing Buddy, so that some sticks out on both sides. At this point you can lube the grooves which are on the side of the bushing buddy for a smoother experience, but this is not necessary. Next, put your Bushing on top of the rubber ball, with the side you want to sand facing up. After that, put the hat on top of the body, making sure that the notches on the sides are aligned with the grooves. Then rotate the hat 10 times while applying light downward pressure from the top.

After that, take the hat off and [[#Strop]] the bushing.

After that, you should check if your bushing is uneven and make it even again as described here: [[#Uneven_Bushing]].

Check the tolerances as described in this chapter: [[#Checking_Tolerances|Checking Tolerances]] and repeat as needed.

===Troubleshooting Bushings===

Here are some common issues, along with tips, tricks and solutions to help diagnose and fix problems when your balisong doesn't behave as expected.

====Adjustable Handle Gap====

If your handle gap shrinks when you press the handles together, for some balisongs, this is normal. However, if the change is excessive, it's likely that the [[#Inner Diameter]] of your bushing is too large.

====Handles Move Forwards And Backwards====

If your handles shift or "click" forward and backward (towards or away from the blade when your balisong is open), the [[#Outer Diameter]] of your bushing is likely too small.

====Unexpected Binding====

Binding that happens even though the balisong seems properly assembled can have several causes.

=====Wrong Sized Washer=====

It is important to use the correct washers for your balisong. Bushings aren't the only thing that will impact your tune.

======Wrong Thickness Of Washer======

Check the height of the [[washer]] that you currently have installed in your balisong. Some balisongs, like the [[Bladerunners_Systems_Replicant_V3|Replicant]] require thinner washers than most other balisongs.

======Different Outer Diameter Of Washer======

Some blades taper (become thinner) towards the bushing. Changing to washers with a different OD alters the clearence between the [[washer]] and blade: if you use new washers with a smaller OD than your previous washers, your balisongs tolerances might become a lot loser and on the flipside: if your new washers have a larger OD than your previous, your balisong might start binding.

=====Uneven Bushing=====

This is the most common cause for binding. A small amount of unevenness is usually acceptable, but the tighter your tune, the less tolerance there is before your balisong starts to bind. For example a difference of 0.030mm might not cause issues on a loose tune, but even a difference of 0.010mm can cause binding on a tight tune.

Stainless steel washers are especially problematic with uneven bushings because the hard [[washer]] will get forced into the blade, causing the edge of the [[washer]] to grind into the blade. This issue is far less severe with phosphor bronze washers, as the softer material will "glide" against the blade even if the bushing is not perfectly flat.

Unfortunately currently there is no way to prevent uneven bushings, however you can minimize the chance of making your bushing uneven by buying slightly oversized bushings. This way, you will spend as little time as possible on the lapping surface, reducing the chances of introducing uneveness. However, this method comes with its own set of problems as this method is very unreliable and some bushing sellers, like [[TheTrueLink]] have been known to send out bushings that are shorter than advertised.

=====Fix Uneven Bushing=====

If you do not have a micrometer, there unfortunately is no precise way to confirm unevenness.

Begin by taking measurements at multiple points around the flat face of the bushing and note each reading. The greater the difference between the smallest and biggest measurement, the more uneven your bushing is. Identify the area with the highest measurement, this is the part that needs to be sanded.

======Fix Uneven Bushing By Hand======

Place the bushing on your lapping surface and apply only preassure on the side that had the highest measurement while grinding the bushing against the lapping surface. This will remove material from the entire side you are sanding, but significantly more from the are where you apply pressure, so if you tune was already very tight, this procedure will probably undersize the bushing.

======Fix Uneven Bushing With A Pivot Lap======

Assemble your pivot lap as described in [[Pivot_System#KnifeDogs_Pivot_Lap]] and apply lots of pressure to the puck and '''almost no pressure at all''' on the plunger. Do lots of passes, around 50-100 depending on how uneven your bushing is and how far away from the target thickness you are and use the same technique of rotating the entire assembly after some amount of motions, as described in the [[#By Hand]] chapter. The flat surface of the pivot lap and low pressure of the plunger which rests on top of the bushing will make sure that almost all of the pressure is only applied to the thicker side of the bushing.

=====Uneven Washers=====

Washers usually do not become uneven on their own, especially if they are stainless steel washers, but just like with uneven bushings, uneven washers can also cause binding. As with an [[#Uneven_Bushing]], you can try sanding the side of the [[washer]] that is thicker. However, removing too much material can lead to other issues, such as the chanwich seam on [[Squid_Industries_Tsunami|Tsunamis]] opening up. In most cases, you're better off simply replacing the washer.

=====Uneven Blade=====

To check if your blade is uneven, measure the area around the pivot hole, where the [[washer]] would normally contact the blade. If the thickness varies, the blade is uneven. Fixing this is extremely difficult. While sanding the thicker area, as described in [[#Uneven Bushings]] might seem like a solution, it is not practical as this method is not precise enough for a blade. Proper correction would require a surface grinder, which most people don't have access to. Your best option is to run the balisong with a looser tune. Some people try using stainless steel washers, hoping the harder material will gradually wear down the uneven blade, but this can cause other issues and is generally not recommended unless your bushings are perfectly even and you're okay with experimenting.

=====Used-Up Washer=====

This mostly affects phosphor bronze or brass washers, as stainless steel washers are too hard to get deformed significantly.

Phosphor bronze or brass Washers will wear down with time and they will develop a groove in the center due to the pressure from the bushing. When you reassemble your balisong, it's pretty much impossible to align the bushing perfectly with that groove again. As a result, one side of the [[washer]] will press harder against the blade than the other, which can lead to binding.

To fix this issue, you should use new washers every time you re-assemble your balisong. This however can get very expensive very fast and is unnecessary if your tune is not tight. Instead you can try to lightly sand both sides of the [[washer]] with a high grit [[#Lapping_Surface]] until the wear marks are completely gone. This usually only takes a couple of circles or figure-eights per side, as phosphor bronze and brass is a lot softer than stainless steel. After that, you can [[Strop]] the surface of the washer. Do about 100 circles or figure-eights per side. Stropping removes almost no, if any material, but helps to refine the surface further. After stropping, your washers should have a reflective finish, though not quite necessarily a full mirror polish.

You can also try applying pressure to the pivot area as if you were trying to snap the handles off the blade. For a visual demonstration, watch this video: [https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316 https://youtu.be/tcGMmcxFaQM?feature=shared&t=1316] and jump to the 21:56 mark.

At this point, reassemble your balisong and check the tune by [[#Feel]]. If the binding is still present, but reduced, you can repeat the process. Just be careful to not remove too much material, or you may end up with new problems which are described in [[#Uneven_Washers]]. If the washers become thinner than 0.010mm of what they should be, consider replacing them as they will very likely cause binding if you balisong has a tight tune.

==Floating Washer==

===Tuning floating bushings===

==Bearing==

==Checking Tolerances==

Checking the tolerances is very important to ensure that you are tuning your balisong correctly.

===Micrometer===

A micrometer is not necessary, but '''highly''' recommended, as it makes it much easier to identify what kind of bushing you are working with (undersized/oversized/uneven).

====Usage====

Before measuring any surface, make sure that the surface you want to measure is free from any dust or oil. The same goes for the spindle and anvil of the micrometer. After that, you need to make sure your micrometer is zeroed correctly. Start by fully closing the measuring gap of your micrometer. Then press the "zero" or "ABS" button. Once it's zeroed, open the micrometer, insert your bushing and close the measuring gap of the micrometer.
Important: Never force the micrometer shut. Always use the ratcheting wheel (the one that makes the clicking sound) to apply even and consistent pressure. Forcing it can damage the tool and will give false readings.

===Feel===

There are multiple tests you can do to check your balisongs tune by feel. For all of those tests, you will need to assemble and lube your balisong.

====Horizontal Swing Test====

Open the balisong and hold it in the standard grip in your hand. Now release the handle that's further from your palm while still holding onto the handle that's closer to your palm. Slightly tilt your hand so that the handle that's further away from your palm can rotate around the pivot. If the rotating handle feels "sticky/gummy", you have bind. Another way to spot bind with this test, is that the blade will sometimes begin to move with the handle. You should be able to fully close and open the handle while holding the balisong horizontal without the blade moving at all.

====Vertical Swing Test====

Hold the balisong Vertically in it's open position and release the lower handle. If the lower handle stops abruptly or feels "sticky/gummy" instead of swinging freely, you have bind.

====Ice Pick Sound Test====

Lots of community members prefer to do an Ice Pick sound test to test their tolerances. This test allows to quickly check for bind and how tight the tolerances are. If the tolerances are tight and you have no bind, the balisong will sound like two [https://en.wikipedia.org/wiki/Neodymium_magnet neodymium magnet] which have attracted each other. To do this test, hold the balisong in the Ice Pick grip, drop the handle that's further away from your palm and quickly pull it back up while slowly bringing your fingers together to close the balisong. This will vibrate the handles back and forth. This test unfortunately doesn't work very well for every balisong, as some balisongs are naturally bouncier than others. For a visual demonstartion, watch this video: [https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35 https://youtu.be/Eo4GhERhS0o?si=v8MujIznSF3F48Sq&t=35]

====Tap Test====

Tap can be tested on both handles at the same time, or only one at a time.

====Wiggle Test On Both Handles====

Hold the balisong as if you are about do do a double rollout. From that position, grip the handle that is closer to your palm and tilt the knive to the right if you are right-handed, left if you are left-handed. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

====Wiggle Test On One Handle====

To check for wiggle only on one handle, hold the balisong in the exact same way as described in the previous chapter [[Wiggle Test On Both Handles|#Wiggle Test On Both Handles]]. Now drop the lower handle so that it touches your palm and pinch the blade between your index and thumb, but be careful not to cut yourself. The blade should be inside the channel of the handle that is higher up. Now shake the balisong forwards and backwards quickly. If you can feel the balisong rattling/moving, you have play. If you can hear a "clicking/tapping" sound, then you have [[tap]].

==Conversion==

It is possible to convert different types of bushing systems.

===Floating Washers To Traditional===

A floating bushing system can be converted to a traditional bushing system.
Currently the instructions are missing on how to do this, but a [[Community_Members|community member]] called [https://www.youtube.com/@taktyc/videos Taktyc] has created a [https://www.youtube.com/watch?v=J08_tFzMsrM video] in which he announced that he will make a tutorial about this.

===Washer To Bushing===

Balisong List

2026-05-02T00:22:03Z

DexyStorm: fix kershaw lucha

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW x Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[JK]]
| [[JK Embargo|Embargo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Emissary|Emissary]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK G10 Orca|G10 Orca]]
| S35VN
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
| Ti
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N/CPM-20CV
| [[Construction#Sandwich|Sandwich]]
| Steel/Ti + Cf
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="32" | [[Squid Industries]]
| [[Squid Industries Hydro|Hydro]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| 6AL-4V Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
| [[Construction#Sandwich|Sandwich]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L; 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C; 410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squidtrainer V1]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1.5|Squidtrainer V1.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squidtrainer V2]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2.5|Squidtrainer V2.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squidtrainer V3]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3.5|Squidtrainer V3.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squidtrainer V4]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L; 410
| [[Construction#Sandwich|Sandwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Triton V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Triton V2]]
| 301HH
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| 6AL-4V Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-04-28T06:39:26Z

DexyStorm: add mako v5 live blade steel

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

MachineWise Slift V2

2026-04-26T20:15:10Z

DexyStorm: add clarification

[[File:MachineWise_Slift_V2.jpg|600px|thumb|right|Rose Gold Slift V2]]

==Overview==

The Slift V2 is a [[Construction#Channel]] titanium balisong made by [[MachineWise]].

==Description==

In its closed position, it is 14,8cm long.

In its open position, it is 26,2cm long.

Without the weights installed, it is 114g

====Handle====

=====Handle Design=====

The Slift V2 uses a [[Construction#Channel]] design, with [[Pin_System#Press-fit]] zen pins.

=====Handle Dimension=====

Most Slift V2 have a [[Speed_Channel|speed channel]]. The faces have three chamfered cutouts which get increasingly wider and longer towards the end of the handle. The shortest cutout is 3.3cm long and 5,0-5,8mm wide. The middle cutout is 3,41cm long and 6-6.8mm wide. The last cutout located near the end of the handles is 3,5cm long and 6.9-7,7mm wide

The speedchannel has a length of 9.62cm and is 5mm wide all across.

The handles have a face to face thickness of 12.875mm

The handles are [[Taper|tapered]] and are 9.860mm wide near the pivots and 12.673mm wide near the end.

=====Handle Weight=====

One handle with no weights, but with the zen pin installed, weighs 39g.

====Blade====

Slift V2 either have a S35VN or AEB-L blade steel.

=====Blade Design=====

The Slift V2 features a bowie style blade with a clip point design. The blade has has a recurve, no sharpening choil, plunge grind or any form of sharpening guide. The edge smoothly transitiones into the plunge. The spine of the blade is chamfered and rounded.

=====Blade Dimensions=====

The blade is exactly 13,0cm long and the cutting edge is 10,7cm long.

The blade is around 3.183mm thick near the washer area.

=====Blade Weight=====

The blade, with no hardware installed, weighs 31g.

===Balance===

Without the bottom Hardware, the center of mass is 4cm away from the beginning of the handles. With the bottom hardware installed, it is 4,4cm

==Hardware==

Slift V2 uses [[MachineWise#In-house_Hardware]].

==History==

The Slift V2 released in late December of 2022 and was discontinued in February of 2024.

It is based on the Slift V1.

===Blade Steel===

The first batch of Slift V2 had AEB-L blades. The blade steel was later changed to S35VN.

===Differences===

The first couple of batches of Slift V2 had the exact same blade as the Slift V1. In later batches, [[MachineWise]] has decided to laser engrave their logo into the blade instead of milling it and completely removing the machining lines.

The jimping on the faces was removed.

===Trivia===

====In House Hardware====

Later versions of the Slift V2 started to use [[MachineWise]]'s own [[MachineWise#In-house_Hardware]].

Balisong List

2026-04-24T18:01:36Z

DexyStorm: add Monarch V3

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[JK Monarch V2|Monarch V3]]
|S35VN
|[[Construction#Channel|Channel]]
|Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-04-22T13:09:49Z

DexyStorm: add "mm" to the small guide on how to read measurements

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770mm and an outer diameter of 9.675mm. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Construction

2026-04-21T13:50:30Z

DexyStorm: update the definition of channel

The construction of a balisong refers to the construction method of the handles.

==Construction types==

Balisongs currently have 3 different types of construction.

===Channel===

Channel means that the knive is usually made out of one single block of metal. Usually the metal in question is either Titanium, or 7075 Aluminium. An example for this type of construction is the [[Squid_Industries_Krake_Raken|Krake Raken]]. <br>
In some rare cases, channel handles may include scales mounted on top, but the underlying structure remains a single-piece channel. For example, the [[Squid_Industries_Nautilus|Nautilus]] is a channel knife with scales, which are held in place by the pivot screws, and by the screws at the end of the handles.
An easy way to to determine whether a balisong has a channel construction is if the blade is enclosed by a continuous piece of material from the blade’s point of view, it is channel construction.

===Sandwich===

The handles of sandwich knives usually incorporate some form of spacer. Spacers come in different sizes pins/standoffs/chunks and can be made from different materials for example: Aluminium, Titaniun, G10, Ultem and many more. Spacers get sandwiched between 2 handle halves. Those handle halves come in two sub-categories:

====Liner====

Liners are the part that touch and sandwich the spacer. If a balisong uses liners, it will also require some form of scales. Those scales sit on top of the liners and sandwich those. The construction for sandwich balis which use liners looks something like this: scale-liner-spacer-liner-scale. An example for this type of construction is the [[Bladerunners_Systems_Replicant|Replicant]].

====Slab====

If the balisong uses only one solid, single piece to sandwich the spacers, those pieces are called "slabs". Slabs are usually made either out of Aluminium or Titanium. An example for this type of construction is the [[Bladerunners_Systems_Titanium_Barebones|Titanium Barebones]].

===Chanwich===

Chanwich means that a handle is made out of 2 handle halves, with no spacer in-between. An example for this type of construction is the [[Squid_Industries_Tsunami|Tsunami]].

==Comparison and Trade-offs==

Every construction method has advantages and disadvantages, so there is no best choice. As a rule of thumb: the more parts the balisong has, the more points of failure it will have, making it less rigid compard to a balisong that has a channel design. That is why it is recommended to use a knives which have a channel design for [[Beater|beaters]] and [[Every_Day_Carry|Every day carry]] use.<br>
That said, sandwich designs are highly regarded for their modability. For example you can swap out the G10 scales of a [[Bladerunners_Systems_Replicant|Replicant]] for scales for ones with a different look or feel.<br>
Chanwich handles also has an advantages: they try to combine the rigidity of channel construction, with the flexibility to incorporate hidden zen pins into the design.

Pin System

2026-04-21T13:40:01Z

DexyStorm: added info that shielded zen is only used on channel knives

Pin Systems are used to keep the blade from hitting the inside of the the handles and to keep the handles from hitting each other. The latter is called [[slap]].<br>

==Material Hardness==

To understand the pros and cons of every pin system, it's important to first learn about material hardness.

There are many different scales on which hardness can be measured, but the most widely-used for steel is the [https://en.wikipedia.org/wiki/Rockwell_hardness_test Rockwell Hardness scale C]. It is often abbreviated to HRC.

Properly heat-treated steel typically falls in the 59-68HRC range, depending on the steel.<br>
Non-heat-treated steel is generally around 35-41HRC.<br>
Titanium usually has a hardness of about 36-38HRC.

The higher the HRC number, the harder the material. Harder materials are more brittle, which means they are more prone to snapping, cracking or shattering. Softer materials (lower HRC) are more malleable and deform under stress rather than breaking. For example: The handles of the [[Nabalis_Canyon|Canyon]] are very thin and are made out of heat-treated stainless steel. Some users have reported that their handles have snapped after drops. Meanwhile, the [[MachineWise_Slift_V2|Slift V2]] also has very thin handles, but they are made of titanium. Rather than snapping, titanium will generally just deform because of its lower hardness.

If two materials that both have a high HRC hit against each other, one, if not both of those materials will be at risk of snapping, cracking or shattering.<br>
If two materials with different hardness ratings make contact, the softer one will always yield to the harder one, meaning that the softer material will get squised and deformed.
If two materials that both have a low HRC hit against each other, both of those materials with squish and deform each other, but the ammount is very small.

==Different Pin Systems==

There are currently three types of pin systems used in balisongs.<br>

===Zen Pin===

If the stopping mechanism is a stainless steel pin housed inside the handle, it is called a "zen pin" system. There are multiple implementations of zen pin systems, but they all have in common that a pin is inside the handle.

Zen pins can be found on both aluminium and titanium balisongs.

====Press-fit====

Press-fit Zen pins are typically only used in [[Construction#Channel|Channel]] balisongs, as this system depends on the structural rigidity that channel construction provides. A stainless steel pin is pressed into a hole which is slightly smaller than the pin itself, creating a tight [https://en.wikipedia.org/wiki/Interference_fit interference fit]. The pin is held in place by friction generated from the pin being slightly larger than the hole, ensuring it stays securely in place during use. An example of a balisong which uses this type of Pin system is the [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]].

====Glued====

Glued zen pins are usually only found on cheap balisongs. They function the same way as [[#Press-fit]] zen pins, with the only difference being that they are held in place with adhesive, rather than by friction. As a result, they tend to fall out much more easily. If a glued zen pin comes loose, it can usually be reinstalled using Loctite or another suitable adhesive.

====Screw Zen====

The screw zen system is only used in [[Construction#Channel]] or [[Construction#Sandwich]] construction knives. The screw zen pin system uses a [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=667aadb5d&_ss=r threaded shoulder pin], or just a [https://thetruelink.com/products/3-16-stainless-straight-pivot-6-64 threaded barrel]. Threaded shoulder pins are usually held in place by a small cutout in the handle in which the pin snaps into place, making the screws not necessarry for this type of construction to work. The problem with this type of Pin System is that over time the should pin will press into the handle, reducing the space between the handle and the blade. As a result, your balisong will bind if you crank the zen screws. You can temporarily fix this by using thinner [[Washer|washer]]s, not using zen pin screws or by using very oversized bushings. If the problem becomes too severe, only replacing the slab or liner will fix it. The barrels, however, are usually held in place by just the screws, meaning that no part of the barrel is pressing into the handle. An example for a balisong with a threaded shoulder pin is the [[Bladerunners_Systems_Replicant|Replicant]] and an example of a screw barrel system is the [[Henninger_Design_Telesto_v3|Telesto v3]].

The screw zen system is sometimes called "Tunable zen system", implying that it can be tuned. This is however misleading because if your balisong [[Bind|binds]] when tightening the zen screws, the issue usually never lies with the screws, but with the [[Bushing|bushings]], or [[Washer|washers]]. If you want to learn more about this, check out [[Pivot_System#Unexpected_Binding]].

====Hidden Zen====

Hidden zen pins can only be used if the balisong utilizes a construction method in which a piece of material sits above the zen pin. An example for a [[Construction#Sandwich|Sandwich]] construction knife with a hidden zen system is the [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]] an example for a [[Construction#Chanwich|Chanwich]] knife with a hidden zen system is the [[Squid_Industries_Tsunami|Tsunami]] and an example for a [[Construction#Channel|Channel]] knife with a hidden zen system is the [[Nabalis_Crescent|Crescent]].

====Shielded Zen====

Shielded Zen pins function the exact same way as [[#Hidden_Zen]] pins, except that they are only used on a channel knives. A small section which includes the section around the [[Pivot_Sexbolt]] is removed from the handle and a slot for the zen pin is machined into the handle, simmiliar to a [[#Press-fit]] setup. Once the zen pin is installed, the removed section is reattatched and held in place by the [[Pivot_Sexbolt]]. This pin system was invented by [[Jimpy]]. Here is a video demonstration: [https://www.instagram.com/p/CzzWaUkPGBy/ https://www.instagram.com/p/CzzWaUkPGBy/]

====Heat-treated vs Non-heat-treated Zen Pins====

Heat-treated zen pins run the risk of shattering, because the hard blade is hitting the hard zen pins, while non-heat-treated zen pins will gradually deform over time, making the handle gap smaller, as described in [[#Material_Hardness]]. An example for a balisong which utilizes heat treated zen pins, is the [[Bladerunners_Systems_Replicant|Replicant]]. An example for a balisong which utilizes non heat treated zen pins, is the [[Squid_Industries_Krake_Raken|Krake Raken]].

===Tang Pin===

Tang pins work very similarily to [[#Press-fit|press fit zen pins]]. The biggest difference is that a single pin is pressed inside the blade. An example for this type of pin system is the [[Bladerunners_Systems_Alpha_Beast_3.0|Alpha Beast 3.0]].

While there are tang pin balisongs with aluminum handles, such as the [[Squid_Industries_Nautilus|Nautilus]], tang pins generally do not work well with aluminium. This is because the unhardened tang pin is still significantly harder than aluminium, causing the aluminium handles to deform over time. As a result, the handle gap will degrade, eventually leading to [[slap]]

====Heat Treated vs Non Heat Treated Tang Pins====

Tang pins must always be non heat treated, this is because the pin needs to conform to the shape of the hole in the blade during the press-fit process. If the tang was hardened, pressing it into the blade could cause the blade to crack due to the lack of give in both the blade, and the tang pin. Additionally, tang pins directly contact the soft titanium handles. By not heat-treating the tang pin, both materials should have similar hardness, allowing them to deform slightly and absorb impact without causing damange. If the pin were heat-treated, it would be significantly harder than the titanium, causing the titanium to deform and eventually leading to [[slap]].

===Pinsless===

The pinsless system attempts to achieve the same clean aesthetic as [[#Hidden Zen|hidden zen]] pins, but with a [[Construction#Channel|channel]] construction. Instead of using a zen pin, the area of the handle where the pin would normally be inserted is left unmachined. This uncut part of the handle acts acts as a built-in pin. An example of a knife with a pinsless design is the [[JK_Monarch|JK Monarch]]<br>

Due to the difference in hardness between the hardened blade and the soft titanium handles, this type of pin system (or lack thereof) will inevitably cause the handle gap to degrade over time, eventaully leading to [[slap]].

Pin System

2026-04-21T13:39:03Z

DexyStorm: updated hidden zen. updated it based on the info that the crescent is channel and also uses hidden zen

Pin Systems are used to keep the blade from hitting the inside of the the handles and to keep the handles from hitting each other. The latter is called [[slap]].<br>

==Material Hardness==

To understand the pros and cons of every pin system, it's important to first learn about material hardness.

There are many different scales on which hardness can be measured, but the most widely-used for steel is the [https://en.wikipedia.org/wiki/Rockwell_hardness_test Rockwell Hardness scale C]. It is often abbreviated to HRC.

Properly heat-treated steel typically falls in the 59-68HRC range, depending on the steel.<br>
Non-heat-treated steel is generally around 35-41HRC.<br>
Titanium usually has a hardness of about 36-38HRC.

The higher the HRC number, the harder the material. Harder materials are more brittle, which means they are more prone to snapping, cracking or shattering. Softer materials (lower HRC) are more malleable and deform under stress rather than breaking. For example: The handles of the [[Nabalis_Canyon|Canyon]] are very thin and are made out of heat-treated stainless steel. Some users have reported that their handles have snapped after drops. Meanwhile, the [[MachineWise_Slift_V2|Slift V2]] also has very thin handles, but they are made of titanium. Rather than snapping, titanium will generally just deform because of its lower hardness.

If two materials that both have a high HRC hit against each other, one, if not both of those materials will be at risk of snapping, cracking or shattering.<br>
If two materials with different hardness ratings make contact, the softer one will always yield to the harder one, meaning that the softer material will get squised and deformed.
If two materials that both have a low HRC hit against each other, both of those materials with squish and deform each other, but the ammount is very small.

==Different Pin Systems==

There are currently three types of pin systems used in balisongs.<br>

===Zen Pin===

If the stopping mechanism is a stainless steel pin housed inside the handle, it is called a "zen pin" system. There are multiple implementations of zen pin systems, but they all have in common that a pin is inside the handle.

Zen pins can be found on both aluminium and titanium balisongs.

====Press-fit====

Press-fit Zen pins are typically only used in [[Construction#Channel|Channel]] balisongs, as this system depends on the structural rigidity that channel construction provides. A stainless steel pin is pressed into a hole which is slightly smaller than the pin itself, creating a tight [https://en.wikipedia.org/wiki/Interference_fit interference fit]. The pin is held in place by friction generated from the pin being slightly larger than the hole, ensuring it stays securely in place during use. An example of a balisong which uses this type of Pin system is the [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]].

====Glued====

Glued zen pins are usually only found on cheap balisongs. They function the same way as [[#Press-fit]] zen pins, with the only difference being that they are held in place with adhesive, rather than by friction. As a result, they tend to fall out much more easily. If a glued zen pin comes loose, it can usually be reinstalled using Loctite or another suitable adhesive.

====Screw Zen====

The screw zen system is only used in [[Construction#Channel]] or [[Construction#Sandwich]] construction knives. The screw zen pin system uses a [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=667aadb5d&_ss=r threaded shoulder pin], or just a [https://thetruelink.com/products/3-16-stainless-straight-pivot-6-64 threaded barrel]. Threaded shoulder pins are usually held in place by a small cutout in the handle in which the pin snaps into place, making the screws not necessarry for this type of construction to work. The problem with this type of Pin System is that over time the should pin will press into the handle, reducing the space between the handle and the blade. As a result, your balisong will bind if you crank the zen screws. You can temporarily fix this by using thinner [[Washer|washer]]s, not using zen pin screws or by using very oversized bushings. If the problem becomes too severe, only replacing the slab or liner will fix it. The barrels, however, are usually held in place by just the screws, meaning that no part of the barrel is pressing into the handle. An example for a balisong with a threaded shoulder pin is the [[Bladerunners_Systems_Replicant|Replicant]] and an example of a screw barrel system is the [[Henninger_Design_Telesto_v3|Telesto v3]].

The screw zen system is sometimes called "Tunable zen system", implying that it can be tuned. This is however misleading because if your balisong [[Bind|binds]] when tightening the zen screws, the issue usually never lies with the screws, but with the [[Bushing|bushings]], or [[Washer|washers]]. If you want to learn more about this, check out [[Pivot_System#Unexpected_Binding]].

====Hidden Zen====

Hidden zen pins can only be used if the balisong utilizes a construction method in which a piece of material sits above the zen pin. An example for a [[Construction#Sandwich|Sandwich]] construction knife with a hidden zen system is the [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]] an example for a [[Construction#Chanwich|Chanwich]] knife with a hidden zen system is the [[Squid_Industries_Tsunami|Tsunami]] and an example for a [[Construction#Channel|Channel]] knife with a hidden zen system is the [[Nabalis_Crescent|Crescent]].

====Shielded Zen====

Shielded Zen pins function the exact same way as [[#Hidden_Zen]] pins, except that they are used on a channel knives. A small section which includes the section around the [[Pivot_Sexbolt]] is removed from the handle and a slot for the zen pin is machined into the handle, simmiliar to a [[#Press-fit]] setup. Once the zen pin is installed, the removed section is reattatched and held in place by the [[Pivot_Sexbolt]]. This pin system was invented by [[Jimpy]]. Here is a video demonstration: [https://www.instagram.com/p/CzzWaUkPGBy/ https://www.instagram.com/p/CzzWaUkPGBy/]

====Heat-treated vs Non-heat-treated Zen Pins====

Heat-treated zen pins run the risk of shattering, because the hard blade is hitting the hard zen pins, while non-heat-treated zen pins will gradually deform over time, making the handle gap smaller, as described in [[#Material_Hardness]]. An example for a balisong which utilizes heat treated zen pins, is the [[Bladerunners_Systems_Replicant|Replicant]]. An example for a balisong which utilizes non heat treated zen pins, is the [[Squid_Industries_Krake_Raken|Krake Raken]].

===Tang Pin===

Tang pins work very similarily to [[#Press-fit|press fit zen pins]]. The biggest difference is that a single pin is pressed inside the blade. An example for this type of pin system is the [[Bladerunners_Systems_Alpha_Beast_3.0|Alpha Beast 3.0]].

While there are tang pin balisongs with aluminum handles, such as the [[Squid_Industries_Nautilus|Nautilus]], tang pins generally do not work well with aluminium. This is because the unhardened tang pin is still significantly harder than aluminium, causing the aluminium handles to deform over time. As a result, the handle gap will degrade, eventually leading to [[slap]]

====Heat Treated vs Non Heat Treated Tang Pins====

Tang pins must always be non heat treated, this is because the pin needs to conform to the shape of the hole in the blade during the press-fit process. If the tang was hardened, pressing it into the blade could cause the blade to crack due to the lack of give in both the blade, and the tang pin. Additionally, tang pins directly contact the soft titanium handles. By not heat-treating the tang pin, both materials should have similar hardness, allowing them to deform slightly and absorb impact without causing damange. If the pin were heat-treated, it would be significantly harder than the titanium, causing the titanium to deform and eventually leading to [[slap]].

===Pinsless===

The pinsless system attempts to achieve the same clean aesthetic as [[#Hidden Zen|hidden zen]] pins, but with a [[Construction#Channel|channel]] construction. Instead of using a zen pin, the area of the handle where the pin would normally be inserted is left unmachined. This uncut part of the handle acts acts as a built-in pin. An example of a knife with a pinsless design is the [[JK_Monarch|JK Monarch]]<br>

Due to the difference in hardness between the hardened blade and the soft titanium handles, this type of pin system (or lack thereof) will inevitably cause the handle gap to degrade over time, eventaully leading to [[slap]].

Pin System

2026-04-21T13:34:39Z

DexyStorm: update info with zen pins pressing into handles

Pin Systems are used to keep the blade from hitting the inside of the the handles and to keep the handles from hitting each other. The latter is called [[slap]].<br>

==Material Hardness==

To understand the pros and cons of every pin system, it's important to first learn about material hardness.

There are many different scales on which hardness can be measured, but the most widely-used for steel is the [https://en.wikipedia.org/wiki/Rockwell_hardness_test Rockwell Hardness scale C]. It is often abbreviated to HRC.

Properly heat-treated steel typically falls in the 59-68HRC range, depending on the steel.<br>
Non-heat-treated steel is generally around 35-41HRC.<br>
Titanium usually has a hardness of about 36-38HRC.

The higher the HRC number, the harder the material. Harder materials are more brittle, which means they are more prone to snapping, cracking or shattering. Softer materials (lower HRC) are more malleable and deform under stress rather than breaking. For example: The handles of the [[Nabalis_Canyon|Canyon]] are very thin and are made out of heat-treated stainless steel. Some users have reported that their handles have snapped after drops. Meanwhile, the [[MachineWise_Slift_V2|Slift V2]] also has very thin handles, but they are made of titanium. Rather than snapping, titanium will generally just deform because of its lower hardness.

If two materials that both have a high HRC hit against each other, one, if not both of those materials will be at risk of snapping, cracking or shattering.<br>
If two materials with different hardness ratings make contact, the softer one will always yield to the harder one, meaning that the softer material will get squised and deformed.
If two materials that both have a low HRC hit against each other, both of those materials with squish and deform each other, but the ammount is very small.

==Different Pin Systems==

There are currently three types of pin systems used in balisongs.<br>

===Zen Pin===

If the stopping mechanism is a stainless steel pin housed inside the handle, it is called a "zen pin" system. There are multiple implementations of zen pin systems, but they all have in common that a pin is inside the handle.

Zen pins can be found on both aluminium and titanium balisongs.

====Press-fit====

Press-fit Zen pins are typically only used in [[Construction#Channel|Channel]] balisongs, as this system depends on the structural rigidity that channel construction provides. A stainless steel pin is pressed into a hole which is slightly smaller than the pin itself, creating a tight [https://en.wikipedia.org/wiki/Interference_fit interference fit]. The pin is held in place by friction generated from the pin being slightly larger than the hole, ensuring it stays securely in place during use. An example of a balisong which uses this type of Pin system is the [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]].

====Glued====

Glued zen pins are usually only found on cheap balisongs. They function the same way as [[#Press-fit]] zen pins, with the only difference being that they are held in place with adhesive, rather than by friction. As a result, they tend to fall out much more easily. If a glued zen pin comes loose, it can usually be reinstalled using Loctite or another suitable adhesive.

====Screw Zen====

The screw zen system is only used in [[Construction#Channel]] or [[Construction#Sandwich]] construction knives. The screw zen pin system uses a [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=667aadb5d&_ss=r threaded shoulder pin], or just a [https://thetruelink.com/products/3-16-stainless-straight-pivot-6-64 threaded barrel]. Threaded shoulder pins are usually held in place by a small cutout in the handle in which the pin snaps into place, making the screws not necessarry for this type of construction to work. The problem with this type of Pin System is that over time the should pin will press into the handle, reducing the space between the handle and the blade. As a result, your balisong will bind if you crank the zen screws. You can temporarily fix this by using thinner [[Washer|washer]]s, not using zen pin screws or by using very oversized bushings. If the problem becomes too severe, only replacing the slab or liner will fix it. The barrels, however, are usually held in place by just the screws, meaning that no part of the barrel is pressing into the handle. An example for a balisong with a threaded shoulder pin is the [[Bladerunners_Systems_Replicant|Replicant]] and an example of a screw barrel system is the [[Henninger_Design_Telesto_v3|Telesto v3]].

The screw zen system is sometimes called "Tunable zen system", implying that it can be tuned. This is however misleading because if your balisong [[Bind|binds]] when tightening the zen screws, the issue usually never lies with the screws, but with the [[Bushing|bushings]], or [[Washer|washers]]. If you want to learn more about this, check out [[Pivot_System#Unexpected_Binding]].

====Hidden Zen====

Hidden zen pins are only used in [[Construction#Sandwich]] or [[Construction#Chanwich]] construction knives. This is because placing the pin inside the handle requires the handle to be be disassembled, which is not possible on a [[Construction#Channel]] knive. An example for a [[Construction#Sandwich]] construction knife with a hidden zen system is the [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]] and an example for a [[Construction#Chanwich|Chanwich]] knife with a hidden zen system is the [[Squid_Industries_Tsunami|Tsunami]].

====Shielded Zen====

Shielded Zen pins function the exact same way as [[#Hidden_Zen]] pins, except that they are used on a channel knives. A small section which includes the section around the [[Pivot_Sexbolt]] is removed from the handle and a slot for the zen pin is machined into the handle, simmiliar to a [[#Press-fit]] setup. Once the zen pin is installed, the removed section is reattatched and held in place by the [[Pivot_Sexbolt]]. This pin system was invented by [[Jimpy]]. Here is a video demonstration: [https://www.instagram.com/p/CzzWaUkPGBy/ https://www.instagram.com/p/CzzWaUkPGBy/]

====Heat-treated vs Non-heat-treated Zen Pins====

Heat-treated zen pins run the risk of shattering, because the hard blade is hitting the hard zen pins, while non-heat-treated zen pins will gradually deform over time, making the handle gap smaller, as described in [[#Material_Hardness]]. An example for a balisong which utilizes heat treated zen pins, is the [[Bladerunners_Systems_Replicant|Replicant]]. An example for a balisong which utilizes non heat treated zen pins, is the [[Squid_Industries_Krake_Raken|Krake Raken]].

===Tang Pin===

Tang pins work very similarily to [[#Press-fit|press fit zen pins]]. The biggest difference is that a single pin is pressed inside the blade. An example for this type of pin system is the [[Bladerunners_Systems_Alpha_Beast_3.0|Alpha Beast 3.0]].

While there are tang pin balisongs with aluminum handles, such as the [[Squid_Industries_Nautilus|Nautilus]], tang pins generally do not work well with aluminium. This is because the unhardened tang pin is still significantly harder than aluminium, causing the aluminium handles to deform over time. As a result, the handle gap will degrade, eventually leading to [[slap]]

====Heat Treated vs Non Heat Treated Tang Pins====

Tang pins must always be non heat treated, this is because the pin needs to conform to the shape of the hole in the blade during the press-fit process. If the tang was hardened, pressing it into the blade could cause the blade to crack due to the lack of give in both the blade, and the tang pin. Additionally, tang pins directly contact the soft titanium handles. By not heat-treating the tang pin, both materials should have similar hardness, allowing them to deform slightly and absorb impact without causing damange. If the pin were heat-treated, it would be significantly harder than the titanium, causing the titanium to deform and eventually leading to [[slap]].

===Pinsless===

The pinsless system attempts to achieve the same clean aesthetic as [[#Hidden Zen|hidden zen]] pins, but with a [[Construction#Channel|channel]] construction. Instead of using a zen pin, the area of the handle where the pin would normally be inserted is left unmachined. This uncut part of the handle acts acts as a built-in pin. An example of a knife with a pinsless design is the [[JK_Monarch|JK Monarch]]<br>

Due to the difference in hardness between the hardened blade and the soft titanium handles, this type of pin system (or lack thereof) will inevitably cause the handle gap to degrade over time, eventaully leading to [[slap]].

Pin System

2026-04-21T13:23:47Z

DexyStorm: fix Squid Industries Krake Raken V3 linking

Pin Systems are used to keep the blade from hitting the inside of the the handles and to keep the handles from hitting each other. The latter is called [[slap]].<br>

==Material Hardness==

To understand the pros and cons of every pin system, it's important to first learn about material hardness.

There are many different scales on which hardness can be measured, but the most widely-used for steel is the [https://en.wikipedia.org/wiki/Rockwell_hardness_test Rockwell Hardness scale C]. It is often abbreviated to HRC.

Properly heat-treated steel typically falls in the 59-68HRC range, depending on the steel.<br>
Non-heat-treated steel is generally around 35-41HRC.<br>
Titanium usually has a hardness of about 36-38HRC.

The higher the HRC number, the harder the material. Harder materials are more brittle, which means they are more prone to snapping, cracking or shattering. Softer materials (lower HRC) are more malleable and deform under stress rather than breaking. For example: The handles of the [[Nabalis_Canyon|Canyon]] are very thin and are made out of heat-treated stainless steel. Some users have reported that their handles have snapped after drops. Meanwhile, the [[MachineWise_Slift_V2|Slift V2]] also has very thin handles, but they are made of titanium. Rather than snapping, titanium will generally just deform because of its lower hardness.

If two materials that both have a high HRC hit against each other, one, if not both of those materials will be at risk of snapping, cracking or shattering.<br>
If two materials with different hardness ratings make contact, the softer one will always yield to the harder one, meaning that the softer material will get squised and deformed.
If two materials that both have a low HRC hit against each other, both of those materials with squish and deform each other, but the ammount is very small.

==Different Pin Systems==

There are currently three types of pin systems used in balisongs.<br>

===Zen Pin===

If the stopping mechanism is a stainless steel pin housed inside the handle, it is called a "zen pin" system. There are multiple implementations of zen pin systems, but they all have in common that a pin is inside the handle.

Zen pins can be found on both aluminium and titanium balisongs.

====Press-fit====

Press-fit Zen pins are typically only used in [[Construction#Channel|Channel]] balisongs, as this system depends on the structural rigidity that channel construction provides. A stainless steel pin is pressed into a hole which is slightly smaller than the pin itself, creating a tight [https://en.wikipedia.org/wiki/Interference_fit interference fit]. The pin is held in place by friction generated from the pin being slightly larger than the hole, ensuring it stays securely in place during use. An example of a balisong which uses this type of Pin system is the [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]].

====Glued====

Glued zen pins are usually only found on cheap balisongs. They function the same way as [[#Press-fit]] zen pins, with the only difference being that they are held in place with adhesive, rather than by friction. As a result, they tend to fall out much more easily. If a glued zen pin comes loose, it can usually be reinstalled using Loctite or another suitable adhesive.

====Screw Zen====

The screw zen system is only used in [[Construction#Channel]] or [[Construction#Sandwich]] construction knives. The screw zen pin system uses a [https://thetruelink.com/products/5-32-shoulder-pin?_pos=1&_sid=667aadb5d&_ss=r threaded shoulder pin], or just a [https://thetruelink.com/products/3-16-stainless-straight-pivot-6-64 threaded barrel]. Threaded shoulder pins are usually held in place by a small cutout in the handle in which the pin snaps into place, making the screws not necessarry for this type of construction to work. The barrels, however, are usually held in place by just the screws. An example for a balisong with a threaded shoulder pin is the [[Bladerunners_Systems_Replicant|Replicant]] and an example of a screw barrel system is the [[Henninger_Design_Telesto_v3|Telesto v3]].

The screw zen system is sometimes called "Tunable zen system", implying that it can be tuned. This is however misleading because if your balisong [[Bind|binds]] when tightening the zen screws, the issue usually never lies with the screws, but with the [[Bushing|bushings]], or [[Washer|washers]]. If you want to learn more about this, check out [[Pivot_System#Unexpected_Binding]].

====Hidden Zen====

Hidden zen pins are only used in [[Construction#Sandwich]] or [[Construction#Chanwich]] construction knives. This is because placing the pin inside the handle requires the handle to be be disassembled, which is not possible on a [[Construction#Channel]] knive. An example for a [[Construction#Sandwich]] construction knife with a hidden zen system is the [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]] and an example for a [[Construction#Chanwich|Chanwich]] knife with a hidden zen system is the [[Squid_Industries_Tsunami|Tsunami]].

====Shielded Zen====

Shielded Zen pins function the exact same way as [[#Hidden_Zen]] pins, except that they are used on a channel knives. A small section which includes the section around the [[Pivot_Sexbolt]] is removed from the handle and a slot for the zen pin is machined into the handle, simmiliar to a [[#Press-fit]] setup. Once the zen pin is installed, the removed section is reattatched and held in place by the [[Pivot_Sexbolt]]. This pin system was invented by [[Jimpy]]. Here is a video demonstration: [https://www.instagram.com/p/CzzWaUkPGBy/ https://www.instagram.com/p/CzzWaUkPGBy/]

====Heat-treated vs Non-heat-treated Zen Pins====

Heat-treated zen pins run the risk of shattering, because the hard blade is hitting the hard zen pins, while non-heat-treated zen pins will gradually deform over time, making the handle gap smaller, as described in [[#Material_Hardness]]. An example for a balisong which utilizes heat treated zen pins, is the [[Bladerunners_Systems_Replicant|Replicant]]. An example for a balisong which utilizes non heat treated zen pins, is the [[Squid_Industries_Krake_Raken|Krake Raken]].

===Tang Pin===

Tang pins work very similarily to [[#Press-fit|press fit zen pins]]. The biggest difference is that a single pin is pressed inside the blade. An example for this type of pin system is the [[Bladerunners_Systems_Alpha_Beast_3.0|Alpha Beast 3.0]].

While there are tang pin balisongs with aluminum handles, such as the [[Squid_Industries_Nautilus|Nautilus]], tang pins generally do not work well with aluminium. This is because the unhardened tang pin is still significantly harder than aluminium, causing the aluminium handles to deform over time. As a result, the handle gap will degrade, eventually leading to [[slap]]

====Heat Treated vs Non Heat Treated Tang Pins====

Tang pins must always be non heat treated, this is because the pin needs to conform to the shape of the hole in the blade during the press-fit process. If the tang was hardened, pressing it into the blade could cause the blade to crack due to the lack of give in both the blade, and the tang pin. Additionally, tang pins directly contact the soft titanium handles. By not heat-treating the tang pin, both materials should have similar hardness, allowing them to deform slightly and absorb impact without causing damange. If the pin were heat-treated, it would be significantly harder than the titanium, causing the titanium to deform and eventually leading to [[slap]].

===Pinsless===

The pinsless system attempts to achieve the same clean aesthetic as [[#Hidden Zen|hidden zen]] pins, but with a [[Construction#Channel|channel]] construction. Instead of using a zen pin, the area of the handle where the pin would normally be inserted is left unmachined. This uncut part of the handle acts acts as a built-in pin. An example of a knife with a pinsless design is the [[JK_Monarch|JK Monarch]]<br>

Due to the difference in hardness between the hardened blade and the soft titanium handles, this type of pin system (or lack thereof) will inevitably cause the handle gap to degrade over time, eventaully leading to [[slap]].

Community

2026-04-21T13:07:56Z

DexyStorm: fix spacing

==Hubs==

The balisong community is active in many different places.

===Instagram===

The balisong community is most active on Instagram. There you will find flipping clips, sales posts, giveaways and product announcements.<br>
In order to use Instagram properly, you will need to create an Instagram account [https://www.instagram.com/accounts/emailsignup/ https://www.instagram.com/accounts/emailsignup/]. After you have created an Instagram account, you can follow pages or people. Pages will usually just repost stories or posts of other people when they tag the page.<br>

The balisongmarketv2 is the biggest second-hand balisong market. They will repost stories of authentic balisongs which people want to sell or buy.<br>
[https://www.instagram.com/balisongmarketv2/ https://www.instagram.com/balisongmarketv2/]<br>

The balisongmarket4all will repost authentic and clone balisongs which people want to sell or buy.<br>
[https://www.instagram.com/balisongmarket4all/ https://www.instagram.com/balisongmarket4all/]<br>

The eubalisongmarketplace works the in the exact same way as the balisongmarket4all, but it is only for people who live in the [https://en.wikipedia.org/wiki/European_Union EU].<br>
[https://www.instagram.com/eubalisongmarketplace/ https://www.instagram.com/eubalisongmarketplace/]<br>

The balisongclonemarket will repost clone balisongs which people want to sell or buy.<br>
[https://www.instagram.com/balisongclonemarket/ https://www.instagram.com/balisongclonemarket/]<br>

balisong_homepage will sometimes post product announcements and flipping clips. Although they are very slow when it comes to reposting content in which they are tagged in.<br>
[https://www.instagram.com/balisong_homepage/ https://www.instagram.com/balisong_homepage/]<br>

===Reddit===

You do not need to create an account to view posts on reddit, however you will need to create one to create posts and comments. On reddit you will mostly find people asking questions, flipping clips and posts about wanting to buy or sell second-hand balisongs.<br>
[https://www.reddit.com/r/balisong/ r/balisong]<br>

The BalisongSale subreddit is for the second-hand sale and purchase of authentic balisongs.<br>
[https://www.reddit.com/r/BalisongSale/ r/BalisongSale]<br>

The BalisongClones subreddit is for sharing flipping clips, asking questions but also for the second-hand sale and purchase of clone balisongs.<br>
[https://www.reddit.com/r/BalisongClones/ r/BalisongClones]<br>

===Discord===

There are a couple of discord servers, but most of them are very inactive.

[https://discord.com/invite/balisong-community-471299608203493377 Balisong Community].

[https://discord.gg/W7qCfSbKGQ The Flippy Boys], owned by [[camaroEE]].

[https://discord.gg/willhirsch The Will Hirsch Server], owned by [[Will_Hirsch|Will Hirsch]].


===YouTube===

On YouTube you will find a wide variety of content: flipping clips, unboxings, reviews, factory tours, rambling videos, tutorials and much more.
There are several content creators. They will be listed in the table in the next chapter.

{| class="wikitable"
|-
! Name
! Platform
! Content
|-
| [[Big_Flips|Big Flips]]
| [https://youtube.com/@bigflips?si=CSw9oBpfl8IvHePC YouTube]
| Flipping Tutorials
|-
| [[Blade_Bias|Blade Bias]]
| [https://youtube.com/@bladebias?si=nC2vLL9SPPhOG4NL YouTube]
| Rambling, Reviews, Unboxings
|-
| [[Ghost_Flipping|Ghost Flipping]]
| [https://youtube.com/@ghostflipping?si=6MEFENvxjibozXnr YouTube]
| Rambling, Reviews, Unboxings
|-
| [[pez_flips|pez flips]]
| [https://youtube.com/@pez_flips?si=7m86aFlc-Tj7Ii63 YouTube]
| Rambling, Reviews, Unboxings
|-
| [[Taktyc]]
| [https://youtube.com/@taktyc?si=fg9fy61qJaZCkefJ YouTube]
| Rambling, Reviews, Unboxings
|-
| [[The_Buffness|The Buffness]]
| [https://youtube.com/@thebuffnessflips?si=h2_nhukRK-a6EnET YouTube]
| Reviews, Unboxings
|-
| [[Will_Hirsch|Will Hirsch]]
| [https://youtube.com/@willhirsch?si=5yfY6iGf1xXwUKNR YouTube]
| Rambling, Reviews, Unboxings, Factory tours
|}

Community

2026-04-21T13:05:54Z

DexyStorm: updated instagram and reddit communities

==Hubs==

The balisong community is active in many different places.

===Instagram===

The balisong community is most active on Instagram. There you will find flipping clips, sales posts, giveaways and product announcements.<br>
In order to use Instagram properly, you will need to create an Instagram account [https://www.instagram.com/accounts/emailsignup/ https://www.instagram.com/accounts/emailsignup/]. After you have created an Instagram account, you can follow pages or people. Pages will usually just repost stories or posts of other people when they tag the page.

The balisongmarketv2 is the biggest second-hand balisong market. They will repost stories of authentic balisongs which people want to sell or buy.<br>
[https://www.instagram.com/balisongmarketv2/ https://www.instagram.com/balisongmarketv2/]

The balisongmarket4all will repost authentic and clone balisongs which people want to sell or buy.<br>
[https://www.instagram.com/balisongmarket4all/ https://www.instagram.com/balisongmarket4all/]

The eubalisongmarketplace works the in the exact same way as the balisongmarket4all, but it is only for people who live in the [https://en.wikipedia.org/wiki/European_Union EU].<br>
[https://www.instagram.com/eubalisongmarketplace/ https://www.instagram.com/eubalisongmarketplace/]

The balisongclonemarket will repost clone balisongs which people want to sell or buy.<br>
[https://www.instagram.com/balisongclonemarket/ https://www.instagram.com/balisongclonemarket/]

balisong_homepage will sometimes post product announcements and flipping clips. Although they are very slow when it comes to reposting content in which they are tagged in.<br>
[https://www.instagram.com/balisong_homepage/ https://www.instagram.com/balisong_homepage/]

===Reddit===

You do not need to create an account to view posts on reddit, however you will need to create one to create posts and comments. On reddit you will mostly find people asking questions, flipping clips and posts about wanting to buy or sell second-hand balisongs.
[https://www.reddit.com/r/balisong/ r/balisong]

The BalisongSale subreddit is for the second-hand sale and purchase of authentic balisongs.<br>
[https://www.reddit.com/r/BalisongSale/ r/BalisongSale]

The BalisongClones subreddit is for sharing flipping clips, asking questions but also for the second-hand sale and purchase of clone balisongs.<br>
[https://www.reddit.com/r/BalisongClones/ r/BalisongClones]

===Discord===

There are a couple of discord servers, but most of them are very inactive.

[https://discord.com/invite/balisong-community-471299608203493377 Balisong Community].

[https://discord.gg/W7qCfSbKGQ The Flippy Boys], owned by [[camaroEE]].

[https://discord.gg/willhirsch The Will Hirsch Server], owned by [[Will_Hirsch|Will Hirsch]].


===YouTube===

On YouTube you will find a wide variety of content: flipping clips, unboxings, reviews, factory tours, rambling videos, tutorials and much more.
There are several content creators. They will be listed in the table in the next chapter.

{| class="wikitable"
|-
! Name
! Platform
! Content
|-
| [[Big_Flips|Big Flips]]
| [https://youtube.com/@bigflips?si=CSw9oBpfl8IvHePC YouTube]
| Flipping Tutorials
|-
| [[Blade_Bias|Blade Bias]]
| [https://youtube.com/@bladebias?si=nC2vLL9SPPhOG4NL YouTube]
| Rambling, Reviews, Unboxings
|-
| [[Ghost_Flipping|Ghost Flipping]]
| [https://youtube.com/@ghostflipping?si=6MEFENvxjibozXnr YouTube]
| Rambling, Reviews, Unboxings
|-
| [[pez_flips|pez flips]]
| [https://youtube.com/@pez_flips?si=7m86aFlc-Tj7Ii63 YouTube]
| Rambling, Reviews, Unboxings
|-
| [[Taktyc]]
| [https://youtube.com/@taktyc?si=fg9fy61qJaZCkefJ YouTube]
| Rambling, Reviews, Unboxings
|-
| [[The_Buffness|The Buffness]]
| [https://youtube.com/@thebuffnessflips?si=h2_nhukRK-a6EnET YouTube]
| Reviews, Unboxings
|-
| [[Will_Hirsch|Will Hirsch]]
| [https://youtube.com/@willhirsch?si=5yfY6iGf1xXwUKNR YouTube]
| Rambling, Reviews, Unboxings, Factory tours
|}

Bladerunners Systems Alpha Beast V3

2026-04-21T10:52:26Z

DexyStorm: add base template for Alpha Beast

==Overview==

The Alpha Beast V3 is a [[Construction#Sandwich]] titanium balisong made by [[Bladerunners Systems]].

==Description==

====Handle====

=====Handle Design=====

The Alpa Beast V3 uses a [[Construction#Sandwich]] design, with [[Pin_System#Tang]] pins.

=====Handle Dimension=====

=====Handle Weight=====

====Blade====

The blades are either made out of 154CM or S35VN

=====Blade Design=====

=====Blade Dimensions=====

=====Blade Weight=====

===Balance===

==Hardware==

===[[Pivot_System#Bushing]]===

Bladerunners Systems has changed the size of their [[Pivot_System#Bushing]] multiple times. The most recent version uses 3.200mm x 4.775mm x 7.112mm.

==History==

===Differences===

===Trivia===

Maranza Zika V2

2026-04-21T10:44:55Z

DexyStorm: fix zika

==Overview==

The Zika V2 is a [[Construction#Chanwich]] titanium and G10 balisong made by [[Maranza]].

==Description==

====Handle====

=====Handle Design=====

The Zika V2 uses a [[Construction#Chanwich]] design, with [[Pin_System#Hidden]] zen pins.

=====Handle Dimension=====

=====Handle Weight=====

====Blade====

The blades are made out of S35VN steel.

=====Blade Design=====

=====Blade Dimensions=====

=====Blade Weight=====

===Balance===

==Hardware==

==History==

===Differences===

The Zika V2 has smoother and more round scales compared to the V1.

===Trivia===

User talk:DexyStorm

2026-04-21T10:35:21Z

DexyStorm: /* Armed Shark Tsunami bushing sizes */ Reply

== Armed Shark Tsunami bushing sizes ==

Just to let you know, I just verified the measurements of the spare bushings that came with my Armed Shark Tsunami to make sure that I didn't make a mistake. For me the outer diameter is really around 6.984-6.987mm. I bought my Armed Shark Tsunami directly from the Armed Shark store on Taobao on 2025-07-09. [[User:Arnisador|Arnisador]] ([[User talk:Arnisador|talk]]) 19:23, 20 April 2026 (UTC)

:aye all good. the reason why i added "6.324" is because somebody i know who bought a false live AS tsunami a couple of days ago, sent me a pic of his spare bushings today and they are 6.33. i'll ask him to check the bushings that are currently inside his AS tsunami just to 100% verify this
:thanks a lot for your contributions, i appareciate it a ton! :) [[User:DexyStorm|DexyStorm]] ([[User talk:DexyStorm|talk]]) 20:28, 20 April 2026 (UTC)
::I only measured my spare bushings. I can check the ones that are in use next time I take it apart. It could also be that they changed it in their latest production batch, but I don't know why they would do that.
::No problem and thanks for running this wiki. I like to have this overview of the hardware, makes it easier to check compatibility of spare hardware from different balisongs. I wish more people would contribute :) [[User:Arnisador|Arnisador]] ([[User talk:Arnisador|talk]]) 05:21, 21 April 2026 (UTC)
:::alright so the dude let me know that the OD of his bushings that are inside his AS nami have a larger OD than his spare ones. it seems like AS has sent him wrong spare bushing. i've removed 6.324 from the balisong list. thank you for your help! :) [[User:DexyStorm|DexyStorm]] ([[User talk:DexyStorm|talk]]) 10:35, 21 April 2026 (UTC)

Balisong List

2026-04-21T09:34:07Z

DexyStorm: fix AS bushing OD size

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770 and an outer diameter of 9.675. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
| D2
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-04-20T20:51:26Z

DexyStorm: add RAD Prelude

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770 and an outer diameter of 9.675. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Ti|Kite-Ti]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF/G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD_Prelude|Prelude]]
|
| [[Construction#Sandwich|Sandwich]]
|
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.324/6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
|
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne Benchmade 40|BM40]]
| Ti
| [[Construction#Channel|Channel]]
|
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
| 5.943x1.561x2.460x5.01x6.679
| 5.998x1.32x3.975x8.96x10.501
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
| 7.498x1.835x2.913x5.00x6.891
| 7.593x1.858x3.985x9.14x11.029
| 0.509x4.60x10.03
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy Balisong]]
| [[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

User talk:DexyStorm

2026-04-20T20:28:28Z

DexyStorm: /* Armed Shark Tsunami bushing sizes */ Reply

Balisong List

2026-04-20T18:55:41Z

DexyStorm: apparently AS tsunamis have 2 different bushing sizes?

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770 and an outer diameter of 9.675. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" |[[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" |[[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" |[[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" |[[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" |[[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
|[[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
|[[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
|[[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" |[[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[LDY Frank|Frank]]
|POM
|[[Construction#Channel|Channel]]
|POM + Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[LDY Kite-Ti|Kite-Ti]]
|440C
|[[Construction#Channel|Channel]]
|Ti+CF/G10
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[LDY Orion S|Orion S]]
|440C
|[[Construction#Chanwich|Chanwich]]
|7075 AL
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" |[[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
|[[MachineWise Slift V2|Slift V2]]
|S35VN
|[[Construction#Chanwich|Channel]]
|TI
|[[Pin System#Press-fit|Press fit Zen]]
|
|
|
|?x?x6.356
|
|
|
|0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" |[[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
|[[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" |[[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" |[[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" |[[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
|[[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" |[[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" |[[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" |[[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.324/6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" |[[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
|TI
|[[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
|
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
|[[TheOne Benchmade 40|BM40]]
|Ti
|[[Construction#Channel|Channel]]
|
|
|
|
|
|2.970x4.00x5.783
|
|5.46x1.47x2.92x5.00x6.48
|5.50x1.50x3.980x7.50x9.013
|0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
|
|
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
|
|
| 0.5x?x?
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" |[[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" |[[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
|[[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
|[[Construction#Sandwich|Sandwich]]
|TI + G10/CF
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
|[[Construction#Sandwich|Sandwich]]
|TI + G10/CF
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Zippy Balisong]]
|[[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-04-20T13:40:15Z

DexyStorm: add eps knives and info

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770 and an outer diameter of 9.675. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects]]
| [[A51projects Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects Pluto V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW design Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW design Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW Peon V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed Shark]]
| [[Armed Shark Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Dangerous Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed Shark Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard Blue Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Slash God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Demon BRO V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Fortress 2 Spy 2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kirat BRO V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Kratos Black Mood V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade 40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 51 Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade 62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade 99 Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[B.a Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[B.a Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong Reaper V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Reaper V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Rebola V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong Xolo/Reaper V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners Systems]]
| [[Bladerunners Systems Alpha Beast V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Alpha Beast V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Aluminium Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Channeled Alpha Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Replicant V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold Steel Arc Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold Steel FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB Genesis V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB Genesis V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo Industries]]
| [[Dodo Industries IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo Industries Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB Pro Flipper V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[EPS Knives]]
| [[EPS Knives 101 V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V2|101 V2]]
| D2
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101 V3|101 V3]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V1|101t V1]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101t V2|101t V2]]
| D2
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Knives 101ti|101ti]]
| D2
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V1|G10 Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS G10 Wraith V2|G10 Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti+G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V1|Wraith V1]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[EPS Wraith V2|Wraith V2]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="8" |[[Fellowship Blades]]
| [[Fellowship Blades Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Medusa V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship Blades Pit Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Fixedstarknife]]
| [[Fixedstarknife Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" |[[Flytanium]]
| [[Flytanium FLY One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Talisong Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium Zenith V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken Forge Blades]]
| [[Franken Forge Blades Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Geof Dumas Knife and Tool]]
| [[Geof Dumas Knife and Tool Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof Dumas Knife and Tool Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Hansen Metals]]
| [[Hansen Metals Solo|Solo]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Monarch V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Henninger Design]]
| [[Henninger Design Telesto v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Telesto v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Hinderer Knives]]
| [[Hinderer Knives Nieves V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer Knives Nieves V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" |[[Hom Design]]
| [[Hom Design Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom Design G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom Design Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" |[[HR]]
| [[HR Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[JappieBalisong]]
| [[JappieBalisong Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Jewell Knives]]
| [[Jewell Knives Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[Jimpy]]
| [[Jimpy Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Tux CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy Zentinel mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" |[[JK]]
| [[JK G10 Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Orca v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK Ultem Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
|[[JW]]
| [[JW Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
|[[Kershaw]]
| [[Kershaw Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
|[[Kotlin]]
| [[Kotlin Tiny Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" |[[LDY]]
| [[LDY Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Cygnus AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[LDY Frank|Frank]]
|POM
|[[Construction#Channel|Channel]]
|POM + Ti
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Kite-AL V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[LDY Kite-Ti|Kite-Ti]]
|440C
|[[Construction#Channel|Channel]]
|Ti+CF/G10
|[[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[LDY Orion S|Orion S]]
|440C
|[[Construction#Chanwich|Chanwich]]
|7075 AL
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Orion V2|Orion V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius AM|Sirius AM]]
|
| [[Construction#Channel|Channel]]
|
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Sirius V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Vixen V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[Lyphryx]]
| [[Lpyhryx Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" |[[MachineWise]]
| [[MachineWise Delta 4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise Opus V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Opus V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Prysma Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Serif V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Serif V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise Slift V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
|[[MachineWise Slift V2|Slift V2]]
|S35VN
|[[Construction#Chanwich|Channel]]
|TI
|[[Pin System#Press-fit|Press fit Zen]]
|
|
|
|?x?x6.356
|
|
|
|0.522x?x9.675
|-
| [[MachineWise Titanium Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" |[[Maxace]]
| [[Maxace Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Duke 2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Phantom V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Serpent Striker V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Snowy Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Microtech]]
| [[Microtech Tachyon V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech Tachyon V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[MinecraftChickenGod]]
| [[MinecraftChickenGod Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Morph Knives]]
| [[Morph Knives Turbid V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph Knives Turbid V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
|[[Motylknife.co]]
| [[Motylknife.co Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[MXNIUM]]
| [[MXNIUM Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM Swordfish V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" |[[Nabalis]]
| [[Nabalis Bird Of Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Cat V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cat V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Cheese V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis Cheese V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Impulse/Extrusion V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis Vulp Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera Abyss Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Notionflips]]
| [[Notionflips Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" |[[NRB]]
| [[NRB Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Konig V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Nemesis V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[OSP]]
| [[OSP Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" |[[Palethius]]
| [[Palethius Backline V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Backline V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Comp V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Perennial.Concepts]]
| [[Perennial.Concepts Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
|[[Psebaliss]]
| [[Perennial.Concepts Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD]]
| [[RAD Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Remshi]]
| [[Remshi Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" |[[Ryworx]]
| [[Ryworx GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Omeme V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Snowflake]]
| [[Snowflake ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[StaticKnives]]
| [[StaticKnives Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" |[[Squid Industries]]
| [[Squid Industries Krake Raken V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Krake Raken V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid Industries Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Mako V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Nautilus V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Squidtrainer V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Squidtrainer V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Titanium Krake Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid Industries Triton V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid Industries Triton V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid Industries Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Stitched Steel]]
| [[Stiched Steel Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched Steel Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" |[[Svix]]
| [[Svix Gale V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Gale V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix Zephyr V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[TheOne]]
| [[TheOne Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[ThomasBalisong]]
| [[ThomasBalisong Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Tuya]]
| [[Tuya Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[WB Concept]]
| [[WB Concept Gigas V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB Concept Gigas V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy Balisong]]
| [[Zippy Balisong BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy Balisong Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[Armed Shark]]
| [[Armed Shark Squid Industries Krake Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed Shark Squid Industries Nautilus V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed Shark Squid Industries Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" |[[Baliplus]]
| [[Baliplus Fellowship Blades Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus Squid Industries Krake Raken V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Squid Industries Krake Raken V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus Fellowship Blades Medusa V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus JK Orca v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus Bladerunners Systems Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus MachineWise Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus Henninger Design Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus Bladerunners Systems Titanium Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus Squid Industries Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX Henninger Design Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX Bladerunners Systems Titanium Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
|TI
|[[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Blue River]]
| [[Blue River Squid Industries Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue River Krake Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne JK|Channeled Alpha Beast]]
|
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
|[[TheOne Benchmade 40|BM40]]
|Ti
|[[Construction#Channel|Channel]]
|
|
|
|
|
|2.970x4.00x5.783
|
|5.46x1.47x2.92x5.00x6.48
|5.50x1.50x3.980x7.50x9.013
|0.694x4.15x8.02
|-
| [[TheOne JK G10 Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
|
|
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM LDY Cygnus V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
|
|
| 0.5x?x?
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" |[[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[A51projects]]
| [[A51projects Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC Knife Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC Knife Replicant Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Bloqstoys]]
| [[Bloqstoys Krake Raken Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[fingermanipulation]]
| [[Fingermanipulation Replicant scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox Fire Factory Replicant Full Channel Spacers v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox Fire Factory Replicant Full Channel Spacers v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Franken Forge Blades]]
| [[Franken Forge Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken Forge Blades Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Hammer Designs]]
| [[Hammer Designs Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger Design]]
| [[Henninger Design Replicant Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger Design Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass Blades]]
| [[Hourglass Blades Krake Raken Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass Blades Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski Craft]]
| [[Kuski Craft Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK Balisong]]
| [[MCK Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[MinecraftChickenGod]]
| [[MinecraftChickenGod Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius Replican Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Spasmfingers]]
| [[Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" |[[Squiggle Scales]]
| [[Squiggle Scales Krake Raken Rehandles V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales 6X Rehandles V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle Scales Replicant Rehandles V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" |[[StaticKnives]]
| [[StaticKnives Replicant Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives Replicant Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" |[[Freedom Fabrication]]
| [[Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
|[[Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
|[[Construction#Sandwich|Sandwich]]
|TI + G10/CF
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
|[[Construction#Sandwich|Sandwich]]
|TI + G10/CF
|[[Pin System#Hidden Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" |[[Zippy Balisong]]
|[[Zippy Balisong Replicant Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Zippy Balisong Replicant Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Balisong List

2026-04-20T13:21:38Z

DexyStorm: added some LDY stuff

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770 and an outer diameter of 9.675. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot_System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects|A51projects]]
| [[A51projects_Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects_Pluto_V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx_ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW_design_Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW_design_Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW_Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW_Peon_V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW_Peon_V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed_Shark|Armed Shark]]
| [[Armed_Shark_Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Dangerous_Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard_Blue_Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Slash_God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife_Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Demon_V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Demon_V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Demon_BRO_V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Fortress_2_Spy_2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kirat_V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kirat_BRO_V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kratos_V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kratos_Black_Mood_V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade_40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_51_Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade_62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_99_Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[b.a_Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades_Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong_Reaper_V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Reaper_V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Reaper_V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Rebola_V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Rebola_V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Xolo/Reaper_V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners_Systems|Bladerunners Systems]]
| [[Bladerunners_Systems_Alpha_Beast_V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Alpha_Beast_V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Alpha_Beast_V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Aluminium_Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw_Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw_Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Channeled_Alpha_Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Replicant_V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Replicant_V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Replicant_V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold_Steel_Arc_Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold_Steel_FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB_Genesis_V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB_Genesis_V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB_Genesis_V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo_Industries|Dodo Industries]]
| [[Dodo_Industries_IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo_Industries_Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB_Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB_Pro_Flipper_V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB_Pro_Flipper_V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB_Pro_Flipper_V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS_Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS_Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[EPS_Knives|EPS Knives]]
| [[EPS_Knives_101_V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101_V2|101 V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101_V3|101 V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101t_V1|101t V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101t_V2|101t V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101ti|101ti]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship_Blades|Fellowship Blades]]
| [[Fellowship_Blades_Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Pit_Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife_Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife_Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium_FLY_One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Talisong_Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium_U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Zenith_V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Zenith_V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken_Forge_Blades|Franken Forge Blades]]
| [[Franken_Forge_Blades_Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof_Dumas_Knife_and_Tool|Geof Dumas Knife and Tool]]
| [[Geof_Dumas_Knife_and_Tool_Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof_Dumas_Knife_and_Tool_Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air_Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hansen_Metals|Hansen Metals]]
| [[Hansen_Metals_Solo|Solo]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JK_Monarch_V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Monarch_V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives_Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives_Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives_Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives_Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger_Design|Henninger Design]]
| [[Henninger_Design_Telesto_v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger_Design_Telesto_v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger_Design_Telesto_v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer_Knives|Hinderer Knives]]
| [[Hinderer_Knives_Nieves_V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer_Knives_Nieves_V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer_Knives_Nieves_V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom_Design|Hom Design]]
| [[Hom_Design_Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Basilisk_Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR_Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR_H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR_Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong_Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell_Knives|Jewell Knives]]
| [[Jewell_Knives_Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy_Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Tux_CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded_Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Zentinel_mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK_G10_Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK_Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK_Orca_v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Orca_v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Orca_v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK_Ultem_Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW_Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw_Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin_Tiny_Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[LDY]]
| [[LDY_Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Cygnus_AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY Frank|Frank]]
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Kite-AL_V1.5|Kite Al V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY Kite-Beta|Kite-Beta]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
|[[LDY Kite-Ti|Kite-Ti]]
|440C
|[[Construction#Channel|Channel]]
|Ti+CF/G10
|[[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Orion_S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Orion_V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Orion_V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[LDY Orion V2|Orion V2]]
|
|[[Construction#Sandwich|Sandwich]]
|7075 AL
|[[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
|[[LDY Sirius AM|Sirius AM]]
|
|[[Construction#Channel|Channel]]
|
|[[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Vixen_V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Vixen_V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx_Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise_Delta_4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Maryn|Maryn]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise_Opus_V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Opus_V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Prysma_V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Prysma_V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Prysma_Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Serif_V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Serif_V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Slift_V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Slift_V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Titanium_Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace_Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Duke_2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Phantom_V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Phantom_V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Serpent_Striker_V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Serpent_Striker_V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Serpent_Striker_V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Snowy_Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech_Tachyon_V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech_Tachyon_V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech_Tachyon_V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod_Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod_R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod_Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph_Knives|Morph Knives]]
| [[Morph_Knives_Turbid_V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph_Knives_Turbid_V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co_Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM_Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Swordfish_V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Swordfish_V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Swordfish_V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis_Bird_Of_Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Cat_V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Cat_V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Cheese_V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis_Cheese_V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis_Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Impulse/Extrusion_V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Vulp_Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera_Abyss_Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera_Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds_Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds_Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips_Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips_Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB_Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Konig_V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Konig_V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Nemesis_V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Nemesis_V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP_Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius_Backline_V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Backline_V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Backline_V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Comp_V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts_Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts_Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD]]
| [[RAD_Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi_Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi_Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi_Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx_GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi_Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept_Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept_Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept_Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake_ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco_BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco_Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco_Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco_Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives_Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives_Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid_Industries|Squid Industries]]
| [[Squid_Industries_Krake_Raken_V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Krake_Raken_V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Krake_Raken_V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid_Industries_Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Nautilus_V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Nautilus_V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid_Industries_Triton_V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Triton_V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched_Steel|Stitched Steel]]
| [[Stiched_Steel_Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched_Steel_Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix_Gale_V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Gale_V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Gale_V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Gale_V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix_Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne_Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne_Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne_Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong_Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya_Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB_Concept_Gigas_V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB_Concept_Gigas_V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy_Balisong|Zippy Balisong]]
| [[Zippy_Balisong_BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot_System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed_Shark|Armed Shark]]
| [[Armed_Shark_Squid_Industries_Krake_Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed_Shark_Squid_Industries_Nautilus_V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed_Shark_Squid_Industries_Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus_Fellowship_Blades_Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus_Squid_Industries_Krake_Raken_V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus_Squid_Industries_Krake_Raken_V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus_Fellowship_Blades_Medusa_V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus_JK_Orca_v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus_Bladerunners_Systems_Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus_MachineWise_Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus_Henninger_Design_Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus_Bladerunners_Systems_Titanium_Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus_Squid_Industries_Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX_Henninger_Design_Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX_Bladerunners_Systems_Titanium_Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue_River_Squid_Industries_Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue_River_Krake_Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne_JK_|Channeled Alpha Beast]]
|
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne_Benchmade_40|BM40]]
| Ti
| [[Construction#Channel|Channel]]
|
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne_JK_G10_Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
|
|
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM_LDY_Cygnus_V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
|
|
| 0.5x?x?
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects|A51projects]]
| [[A51projects_Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC_Knife_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC_Knife_Replicant_Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys_Krake_Raken_Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken_Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[fingermanipulation_Replicant_scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken_Forge_Blades|Franken Forge Blades]]
| [[Franken_Forge_Blades_Replicant_Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Replicant_Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer_Designs_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger_Design|Henninger Design]]
| [[Henninger_Design_Replicant_Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger_Design_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass_Blades|Hourglass Blades]]
| [[Hourglass_Blades_Krake_Raken_Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass_Blades_Replicant_Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski_Craft|Kuski Craft]]
| [[Kuski_Craft_Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK_Balisong|MCK Balisong]]
| [[MCK_Balisong_Replicant_Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod_Replicant_Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius_Replican_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient_zero_balisong|Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers_Nautilus_Scales|Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers_Replicant_Scales|Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle_Scales|Squiggle Scales]]
| [[Squiggle_Scales_Krake_Raken_Rehandles_V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_6X_Rehandles_V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_6X_Rehandles_V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_Replicant_Rehandles_V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_Replicant_Rehandles_V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives_Replicant_Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives_Replicant_Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom_Fabrication|Freedom Fabrication]]
| [[Freedom_Fabrication_Nautilus_Scales|Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Liners|Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Rehandles|Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Scales|Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Spacers|Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Titanium_Krake_Raken_Rehandles_V1|Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Titanium_Krake_Raken_Rehandles_V2|Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy_Balisong|Zippy Balisong]]
| [[Zippy_Balisong_Replicant_Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Replicant_Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}

Maranza Zika V2

2026-04-18T15:58:13Z

DexyStorm: added base template + difference to v1

==Overview==

The Serif V2 is a [[Construction#Chanwich]] titanium balisong made by [[MachineWise]].

==Description==

====Handle====

=====Handle Design=====

The Serif V2 uses a [[Construction#Chanwich]] design, with [[Pin_System#Hidden]] zen pins.

=====Handle Dimension=====

=====Handle Weight=====

====Blade====

The blades are made out of S35VN steel.

=====Blade Design=====

=====Blade Dimensions=====

=====Blade Weight=====

===Balance===

==Hardware==

==History==

===Differences===

The Zika V2 has smoother and more round scales compared to the V1.

===Trivia===

Balisong List

2026-04-18T15:57:07Z

DexyStorm: add Zika v2

This is a non-exhaustive list of a lot of balisongs with some specifications.<br>

Before you start reading the table, you should familiarize yourself with how to read the measurements.

Some information on how to read measurements is provided in [[Edit_Guide#Measurements]].<br>
Different parts of a component will get segragated by a "x". For example a [[Washer|washer]] with the size of 0.522x4.770x9.675 will have a height of 0.522mm, an inner diameter of 4.770 and an outer diameter of 9.675. If a measurement has a question mark (?) that means that the measurement for this part is missing, unknown or has not been added yet. For example if a [[Washer|washer]] has a measurement of 0.522x?x9.67, that means that the inner diameter of the [[Washer|washer]] is unknown.

The order of components for different parts is as follows:
The spaces before and after every x are only for better readability. There will be no spaces in the actual list.

Screw:<br>

Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Bushing: <br>
Height x Inner Diameter x Outer Diameter

Pin: Pins come in different shapes and sizes, please visit the Page dedicated to the balisong you are interested in for more information.<br>
Length x Thickness

Sexbolt:<br>
Head diameter x Head length x Shaft diameter x Shaft length x Overall length

Washer:<br>
Height x Inner Diameter x Outer Diameter

As a rule of thumb: the components are always listed in alphabetical order.

'''''If you want instructions on how to efficiently edit this table, please re-read [[Edit_Guide#Tables]].'''''

{| class="wikitable"
|-
! colspan="14" | [[Authentic]]
|-
| Brand
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot_System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[A51projects|A51projects]]
| [[A51projects_Pluto V1|Pluto V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects_Pluto_V2|Pluto V2]]
|
| [[Construction#Sandwich|Sandwich]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Acidwrx]]
| [[Acidwrx_ZZYZYX|ZZYZYX]]
| S35
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[AJW design]]
| [[AJW_design_Moroha|Moroha]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AJW_design_Origami|Origami]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[AMKW]]
| [[AMKW_Aeon|Aeon]]
| S35/Nitro-V
| [[Construction#Sandwich|Sandwich]]
| TI / TI+G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW_Peon_V1|Peon V1]]
| S35
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[AMKW_Peon_V2|Peon V2]]
| Nitro-V
| [[Construction#Sandwich|Sandwich]]
| Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Armed_Shark|Armed Shark]]
| [[Armed_Shark_Ajax|Ajax]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Dangerous_Wanderer|Dangerous Wanderer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Eureka|Eureka]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Prism|Prism]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Armed_Shark_Shining|Shining]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Asgard]]
| [[Asgard_Blue_Sky|Blue Sky]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Bunny|Bunny]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Cancer|Cancer]]
|
|
| POM
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Carrot|Carrot]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Master|Master]]
|
|
| Al
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Slash_God|Slash God]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Asgard_Zangetsu|Zangetsu]]
|
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| rowspan="11" | [[Atroposknife]]
| [[Atroposknife_Bastard|Bastard]]
| AUS-8
|
| Brass
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Demon_V1|Demon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Demon_V2|Demon V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Demon_BRO_V2|Demon BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Fortress_2_Spy_2.0|Fortress 2 Spy V2]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kirat_V2|Kirat V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kirat_BRO_V2|Kirat BRO V2]]
| N690
|
| Ti + G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kratos_V2|Kratos V2]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Kratos_Black_Mood_V2|Kratos Black Mood V2]]
| N690
|
|
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Moloch|Moloch]]
| N690
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Atroposknife_Non-Grata|Non-Grata]]
| N690
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="18" | [[Benchmade]]
| [[Benchmade_40|40]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_41|41]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_42|42]]
| 440
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_43|43]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_44|44]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_45|45]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_46|46]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_47|47]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_48|48]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_49|49]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_51_Morpho|51 Morpho]]
| D2
| [[Construction#Sandwich|Sandwich]]
| Ti/G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Benchmade_62|62]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_67|67]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_68|68]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_82|82]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_85|85]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_87|87]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Benchmade_99_Necron|99 Necron]]
| S30V
| [[Construction#Sandwich|Sandwich]]
| SS/TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[b.a]]
| [[b.a_Atlas|Atlas]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Atlas|Nakiri]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Atlas|Seigaiha]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Sparrow|Sparrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[b.a_Atlas|Tesseract]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Biteblades]]
| [[Biteblades_Titan|Titan]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Blackbalisong]]
| [[Blackbalisong_Reaper_V1|Reaper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Reaper_V2|Reaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Reaper_V3|Reaper V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Rebola_V1|Rebola V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Rebola_V2|Rebola V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Blackbalisong_Xolo/Reaper_V2|XoloReaper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="12" | [[Bladerunners_Systems|Bladerunners Systems]]
| [[Bladerunners_Systems_Alpha_Beast_V1|Alpha Beast V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Alpha_Beast_V2|Alpha Beast V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Alpha_Beast_V3|Alpha Beast V3]]
| 154CM/SV35
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Aluminium_Barebones|Aluminium Barebones]]
| 154CM
| [[Construction#Channel|Channel]]
|
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V1|Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw_Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ss
| [[Pin System#Screw_Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Channeled_Alpha_Beast|Channeled Alpha Beast]]
| 154CM/SV35
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
| ?x?x7.112
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Replicant_V1|Replicant V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Replicant_V2|Replicant V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Bladerunners_Systems_Replicant_V3|Replicant V3]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
| 4.139x1.501x2.153x4.516x6.017
| 4.211x?x3.125x?x12.860
| 3.5814x?x6.348
|
| 6.627x?x3.428x?x8.107
| 6.331x?x4.733x?x11.355
| 0.380x?x10.000
|-
| [[Bladerunners Systems Titanium Barebones V1|Titanium Barebones V1]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
| /
|
|
|
|
|
|
|-
| [[Bladerunners Systems Titanium Barebones V2|Titanium Barebones V2]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Cold Steel]]
| [[Cold_Steel_Arc_Angel|Arc Angel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Cold_Steel_FGX|FGX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[DCB]]
| [[DCB_Genesis_V1|Genesis V1]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB_Genesis_V2|Genesis V2]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[DCB_Genesis_V3|Genesis V3]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Dodo_Industries|Dodo Industries]]
| [[Dodo_Industries_IVO|IVO]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Dodo_Industries_Raphus|Raphus]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[ELB]]
| [[ELB_Mamba|Mamba]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB_Pro_Flipper_V1|Pro Flipper V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB_Pro_Flipper_V2|Pro Flipper V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ELB_Pro_Flipper_V3|Pro Flipper V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[EOS]]
| [[EOS_Serpent|Serpent]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EOS_Trident|Trident]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[EPS_Knives|EPS Knives]]
| [[EPS_Knives_101_V1|101 V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101_V2|101 V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101_V3|101 V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101t_V1|101t V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101t_V2|101t V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[EPS_Knives_101ti|101ti]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Fellowship_Blades|Fellowship Blades]]
| [[Fellowship_Blades_Empress|Empress]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Empusa|Empusa]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Gaboon|Gaboon]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V1|Medusa V1]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V2|Medusa V2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V3|Medusa V3]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Medusa_V4|Medusa V4]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Fellowship_Blades_Pit_Viper|Pit Viper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Fixedstarknife]]
| [[Fixedstarknife_Meteor|Meteor]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fixedstarknife_Starlight|Starlight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="6" | [[Flytanium]]
| [[Flytanium_FLY_One|FLY One]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Talisong_Z|Talisong Z]]
| AEB-L
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Tatersong|Tatersong]]
| CPM-154
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Flytanium_U.F.O|U.F.O]]
| 6061 Al
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Zenith_V1|Zenith V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Flytanium_Zenith_V2|Zenith V2]]
| 410
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Franken_Forge_Blades|Franken Forge Blades]]
| [[Franken_Forge_Blades_Galvanis|Galvanis]]
| S35VN
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Ion|Ion]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Static|Static]]
| S35VN;AEB-L
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Voltaic|Voltaic]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Geof_Dumas_Knife_and_Tool|Geof Dumas Knife and Tool]]
| [[Geof_Dumas_Knife_and_Tool_Ex-10|Ex-10]]
| CPM 154
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Geof_Dumas_Knife_and_Tool_Ex-11|Ex-11]]
|
|
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[H-Air]]
| [[H-Air_Dust|Dust]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hansen_Metals|Hansen Metals]]
| [[Hansen_Metals_Solo|Solo]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JK_Monarch_V1|Monarch V1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Monarch_V2|Monarch V2]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Heibel-Knives]]
| [[Heibel-Knives_Invictus|Invictus]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives_Menace|Menace]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives_Sapient|Sapient]]
| RWL34
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Heibel-Knives_Valor|Valor]]
| RWL34
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Henninger_Design|Henninger Design]]
| [[Henninger_Design_Telesto_v1|Telesto v1]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger_Design_Telesto_v2|Telesto v2]]
|
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Henninger_Design_Telesto_v3|Telesto v3]]
| S45VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Hinderer_Knives|Hinderer Knives]]
| [[Hinderer_Knives_Nieves_V1|Nieves V1]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer_Knives_Nieves_V2|Nieves V2]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hinderer_Knives_Nieves_V3|Nieves V3]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Hom_Design|Hom Design]]
| [[Hom_Design_Basilisk|Basilisk]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Basilisk_Elite|Basilisk Elite]]
| S35VN
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Basilisk-R|Basilisk-R]]
| 154CM
| [[Construction#Sandwich|Sandwich]]
| TI / TI + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Chimera|Chimera]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_G10ST|G10ST]]
| G10
| [[Construction#Channel|Channel]]
| G10
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_I-Basilisk|I-Basilisk]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Prodigy|Prodigy]]
| 440C/154CM
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Rhapsody|Rhapsody]]
| 154CM
|
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Hom_Design_Specter|Specter]]
| S35VN/Elmax
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[HR]]
| [[HR_Doom|Doom]]
|
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Dragon-Flood|Dragon Flood]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR_H01|H01]]
| 9Cr18MoV
| [[Construction#Sandwich|Sandwich]]
| Ti + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Judgment|Judgment]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[HR_Killer|Killer]]
| VG10
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Rich|Rich]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[HR_Verdict|Verdict]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JappieBalisong]]
| [[JappieBalisong_Bert|Bert]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Jewell_Knives|Jewell Knives]]
| [[Jewell_Knives_Lyra|Lyra]]
| ?;440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Jimpy]]
| [[Jimpy_Mashin-TR|Mashin-TR]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Sentinel|Sentinel]]
| 440c
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Tux_CM|Tux CM]]
| Ti
| [[Construction#Sandwich|Sandwich]]
| Ti + Glass filled Nylon
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Zentinel|Zentinel]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Shielded_Zen|Shielded Zen]]
|
|
|
|
|
|
|
|
|-
| [[Jimpy_Zentinel_mini|Zentinel mini]]
| MagnaCut
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[JK]]
| [[JK_G10_Orca|G10 Orca]]
|
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
|
|
|
|
|
|-
| [[JK_Litetech|Litetech]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[JK_Orca_v1|Orca v1]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Orca_v1.5|Orca v1.5]]
| S35VN
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Orca_v2|Orca v2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[JK_Regime|Regime]]
| Nitro-V
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[JK_Ultem_Orca|Orca]]
|
| [[Construction#Channel|Channel]]
| Ultem
|
|
|
|
|
|
|
|
|
|-
| [[JW]]
| [[JW_Magnet|Magnet]]
|
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Kershaw]]
| [[Kershaw_Lucha|Lucha]]
| 14C28N
| [[Construction#Sandwich|Sandwich]]
| Steel
|
|
|
|
| /
|
|
|
|
|-
| [[Kotlin]]
| [[Kotlin_Tiny_Cock|Tiny Cock]]
| 7075 AL
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| rowspan="17" | [[LDY]]
| [[LDY_Cygnus|Cygnus]]
| S35VN;3CR13
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
|
|
|
|
|
|
|
|
|
|-
| [[LDY_Cygnus_AL|Cygnus AL]]
| 440C
|
| 7075 AL + CF
|
|
|
|
|
|
|
|
|
|-
|
| POM
| [[Construction#Channel|Channel]]
| POM + Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Kite-Al|Kite-Al]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Kite-AL_V1.5|Kite AL V1.5]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.051x5.01x6.982
|
| 6.80x2.60x3.91x5.88x8.404
| 6.72x2.40x4.978x9.40x11.612
| 0.502x5.20x9.02
|-
| [[LDY_Kite|Kite]]
| 440C
| [[Construction#Channel|Channel]]
| Ti+CF
| Pinselss
|
|
|
|
|
|
|
|
|-
| [[LDY_Orion_S|Orion S]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Orion_V1|Orion V1]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Orion_V1.5|Orion V1.5]]
| 440C;3CR13
| [[Construction#Sandwich|Sandwich]]
| 7075 AL
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V1|Sirius V1]]
|
|
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V2|Sirius V2]]
|
|
| 7075 AL
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V3|Sirius V3]]
| 440C;3CR13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V4|Sirius V4]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Sirius_V4.5|Sirius V4.5]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Vega|Vega]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| G10 + Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Vixen_V1|Vixen V1]]
|
|
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[LDY_Vixen_V2|Vixen V2]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Lyphryx]]
| [[Lpyhryx_Rhynix|Rhynix]]
| Resin
| [[Construction#Channel|Channel]]
| Resin
|
|
|
|
|
|
|
|
|
|-
| rowspan="15" | [[MachineWise]]
| [[MachineWise_Delta_4|Delta 4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Fift|Fift]]
| A2
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Maryn|Maryn]]
|
|
|
|
|
|
|
| ?x?x6.356
|
|
|
|
|-
| [[MachineWise_Opus_V1|Opus V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Opus_V2|Opus V2]]
| S35VN
|
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Prysma_V1|Prysma V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Prysma_V2|Prysma V2]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Prysma_Pro|Prysma Pro]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Sasori|Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Serif_V1|Serif V1]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Serif_V2|Serif V2]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Slift_V1|Slift V1]]
| AEB-L;S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Slift_V2|Slift V2]]
| S35VN
| [[Construction#Chanwich|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| ?x?x6.356
|
|
|
| 0.522x?x9.675
|-
| [[MachineWise_Titanium_Sasori|Titanium Sasori]]
| S35VN;VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[MachineWise_Tottori|Tottori]]
| S35VN;VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Maranza]]
| [[Maranza Zika V1|Zika V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|[[Maranza Zika V2|Zika V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="19" | [[Maxace]]
| [[Maxace_Apostle|Apostle]]
| M390
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Banshee|Banshee]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Covenant|Covenant]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_DMG|DMG]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Duke_2|Duke 2]]
| M30
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Gauss|Gauss]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Loran|Loran]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Obsidian|Obsidian]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Pelican-M|Pelican-M]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Petrel|Petrel]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Phantom_V1|Phantom V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Phantom_V2|Phantom V2]]
| M390/SLD-magic/9Cr18CoMoV
|
| Ti/7075Al
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Scorpius|Scorpius]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Serpent_Striker_V1|Serpent Striker V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Serpent_Striker_V2|Serpent Striker V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Serpent_Striker_V3|Serpent Striker V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Shi|Shi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Snowy_Owl|Snowy Owl]]
| M390
|
| Ti + CF
|
|
|
|
|
|
|
|
|
|-
| [[Maxace_Unicorn|Unicorn]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Microtech]]
| [[Microtech_Tachyon_V1|Tachyon V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech_Tachyon_V2|Tachyon V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Microtech_Tachyon_V3|Tachyon V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[MinecraftChickenGod]]
| [[MinecraftChickenGod_Ender|Ender]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod_R-Drago|R-Drago]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod_Rekuza|Rekuza]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Morph_Knives|Morph Knives]]
| [[Morph_Knives_Turbid_V1|Turbid V1]]
| S35
|
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Morph_Knives_Turbid_V2|Turbid V2]]
| S35
| [[Construction#Channel|Channel]]
| Ti
|
|
|
|
|
|
|
|
|
|-
| [[Motylknife.co]]
| [[Motylknife.co_Lotus|Lotus]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[MXNIUM]]
| [[MXNIUM_Raid|Raid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Skylark|Skylark]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Swordfish_V1|Swordfish V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Swordfish_V2|Swordfish V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MXNIUM_Swordfish_V2.5|Swordfish V2.5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="20" | [[Nabalis]]
| [[Nabalis_Bird_Of_Prey|Bird Of Prey]]
| 440C
| [[Construction#Chanwich|Chanwich]]
| 7075 Al + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Canyon|Canyon]]
| 420
| [[Construction#Channel|Channel]]
| 420
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Cat_V1|Cat V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Cat_V2|Cat V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Cheese_V1|Cheese V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.220x4.8x6.972
|
|
|
| 0.8
|-
| [[Nabalis_Cheese_V2|Cheese V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Crescent|Crescent]]
| 420C
| [[Construction#Channel|Channel]]
| 7075AL + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 3.018x4.8x6.968
|
|
|
| 0.8
|-
| [[Nabalis_Extrusion|Extrusion]]
| 7075 Al
| [[Construction#Channel|Channel]]
| 6063 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Hydra|Hydra]]
| 440C
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Impulse/Extrusion_V2|Impulse/Extrusion V2]]
| 420
| [[Construction#Channel|Channel]]
| 6063-T6 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Lightning|Lightning]]
| 420
| [[Construction#Channel|Channel]]
| 6061
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Marbles|Marbles]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Morse|Morse]]
|
|
|
| [[Pin System#Glued|Glued Zen]]
|
|
|
|
|
|
|
|
|-
| [[Nabalis_Overlord|Overlord]]
| 420
| [[Construction#Sandwich|Sandwich]]
| 6061 Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V1|Reverie V1]]
| 420
| [[Construction#Channel|Channel]]
| 6061 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis Reverie V2|Reverie V2]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al
|
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Trident|Trident]]
| 440
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Vulp|Vulp]]
| 420
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| ?x?x6.985
|
|
|
|
|-
| [[Nabalis_Vulp_Pro|Vulp Pro]]
| AUS10;440C
| [[Construction#Channel|Channel]]
| 7075 Al + G10
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| [[Nabalis_Wing|Wing]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Glued|Glued Zen]]
|
|
|
| x?x?6.324
|
|
|
|
|-
| rowspan="2" | [[Newera]]
| [[Newera_Abyss_Lingyuan|Abyss Lingyuan]]
| 5Cr15
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + Ti
|
|
|
|
|
|
|
|
|
|-
| [[Newera_Sunshine|Sunshine]]
| 3Cr13
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
| 107g
|
|
|
|
|
|
|
|-
| rowspan="2" | [[NoloBuilds]]
| [[NoloBuilds_Chioni|Chioni]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[NoloBuilds_Meraki|Meraki]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Notionflips]]
| [[Notionflips_Atomic|Atomic]]
| unk
| [[Construction#Sandwich|Sandwich]]
| 3d printed(unk)
|
|
|
|
|
|
|
|
|
|-
| [[Notionflips_Surv|Surv]]
| RWL34
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
| 135g
|
|
|
|
|
|
|
|-
| rowspan="10" | [[NRB]]
| [[NRB_Doosh|Doosh]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Konig_V1|Konig V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Konig_V2|Konig V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Nemesis_V1|Nemesis V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Nemesis_V2|Nemesis V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Outcast|Outcast]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_SLight|SLight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Trapcode|Trapcode]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Ultralight|Ultralight]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[NRB_Vortex|Vortex]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[OSP]]
| [[OSP_Matrix|Matrix]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="8" | [[Palethius]]
| [[Palethius_Backline_V1|Backline V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Backline_V2|Backline V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Backline_V3|Backline V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_BC|BC]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Comp_V1|Comp V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Industrial|Industrial]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_Revolution|Revolution]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius_RoninWorks|RoninWorks]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Perennial.Concepts]]
| [[Perennial.Concepts_Kronos|Kronos]]
| S35VN
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Psebaliss]]
| [[Perennial.Concepts_Rage|Rage]]
| 440c
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[RAD]]
| [[RAD_Cygnus|Cygnus]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Remshi]]
| [[Remshi_Aluno|Aluno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| 7075 Al
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi_Kuno|Kuno]]
| Ti
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Remshi_Shino|Shino]]
| 440C
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="9" | [[Ryworx]]
| [[Ryworx_GA|GA]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V1|Omeme V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V2|Omeme V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V3|Omeme V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V4|Omeme V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V5|Omeme V5]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Omeme_V6|Omeme V6]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Konohishi|Konohishi]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Ryworx_Setsuna|Setsuna]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[SharpFlippyBoi]]
| [[SharpFlippyBoi_Corvus|Corvus]]
| S35vn
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
| /
| /
| x?x?7.000
| 7.495x2.974
|
| ?x?x4.473x?9.614
|
|-
| rowspan="3" | [[Shatteredconcept]]
| [[Shatteredconcept_Rift|Rift]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept_Ruined|Ruined]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Shatteredconcept_Shattered|Shattered]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Snowflake]]
| [[Snowflake_ABX|ABX]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Spyderco]]
| [[Spyderco_BaliYo|BaliYo]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco_Spyderfly|Spyderfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco_Smallfly|Smallfly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spyderco_Szabofly|Szabofly]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[StaticKnives]]
| [[StaticKnives_Artemis|Artemis]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives_Icarus|Icarus]]
| 440c
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="28" | [[Squid_Industries|Squid Industries]]
| [[Squid_Industries_Krake_Raken_V1|Krake Raken V1]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Krake_Raken_V2|Krake Raken V2]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Krake_Raken_V2.5|Krake Raken V2.5]]
|
| [[Construction#Channel|Channel]]
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Krake_Raken_V3|Krake Raken V3]]
| AEB-L;410
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
| 0.5
|-
| [[Squid_Industries_Madko|Madko]]
| 410
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V1|Mako V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V2|Mako V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V3|Mako V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V4|Mako V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V4.5|Mako V4.5]]
|
| [[Construction#Channel|Channel]]
| 6061 AL
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Mako_V5|Mako V5]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Nautilus_V1|Nautilus V1]]
| 410
| [[Construction#Channel|Channel]]
| 6061 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Nautilus_V2|Nautilus V2]]
| 440C;410
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Swordfish|Swordfish]]
| 7075 AL
| [[Construction#Chanwich|Chanwich]]
| 7075 AL
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squiddy|Squiddy]]
| CPVC
| [[Construction#Channel|Channel]]
| CPVC
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-A|Squiddy-A]]
| CPVC
| [[Construction#Channel|Channel]]
| Ultem
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-AL|Squiddy-AL]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-B|Squiddy-B]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-U|Squiddy-U]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squiddy-WH|Squiddy-WH]]
| Acetal
| [[Construction#Channel|Channel]]
| Acetal
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V1|Squiddy-Squidtrainer V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V2|Squiddy-Squidtrainer V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V3|Squiddy-Squidtrainer V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Squidtrainer_V4|Squiddy-Squidtrainer V4]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Titanium_Krake_Raken|Titanium Krake Raken]]
| AEB-L;410
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
| 6.850x?x?
|-
| [[Squid_Industries_Triton_V1|Squiddy-Squidtrainer Triton V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squid_Industries_Triton_V2|Squiddy-Squidtrainer Triton V2]]
| 6061 AL
| [[Construction#Channel|Channel]]
| 6061 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| /
|
|
|
|
|-
| [[Squid_Industries_Tsunami|Tsunami]]
| S35VN
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Stitched_Steel|Stitched Steel]]
| [[Stiched_Steel_Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Stiched_Steel_Paradigm|Paradigm]]
| S35VN
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="10" | [[Svix]]
| [[Svix_Gale_V1|Gale V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Gale_V2|Gale V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Gale_V3|Gale V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Gale_V4|Gale V4]]
| 440C
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix_Terra|Terra]]
| 440C
| [[Construction#Channel|Channel]]
| 6061Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V1|Zephyr V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V2|Zephyr V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V3|Zephyr V3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V4|Zephyr V4]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Svix_Zephyr_V4.5|Zephyr V4.5]]
| 440C
| [[Construction#Channel|Channel]]
| 7075 Al
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tayflipper]]
| [[Calico]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne_Alien|Alien]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne_Arrow|Arrow]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[TheOne_Falcon|Falcon]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[ThomasBalisong]]
| [[ThomasBalisong_Argon|Aragon]]
| PM204;5CR15
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Astra|Astra]]
| 440C ;S35VN
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Baikal|Baikal]]
| ?;AUS-10
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Default|Default]]
|
| [[Construction#Channel|Channel]]
| 7075 AL + G10 / CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[ThomasBalisong_Refault|Refaultl]]
| 5CR15
| [[Construction#Channel|Channel]]
| 7075 AL + G10 /CF / Ultem
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Tuya]]
| [[Tuya_Starship|Starship]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[WB Concept]]
| [[WB_Concept_Gigas_V1|Gigas V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[WB_Concept_Gigas_V2|Gigas V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Zippy_Balisong|Zippy Balisong]]
| [[Zippy_Balisong_BaliQuill|BaliQuill]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Cycloid|Cycloid]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Parallax|Parallax]]
| S35VN
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Zipper|Zipper]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Clone]]
| Product
| [[Blade Steel]]
| [[Construction]]
| [[Handle Material]]
| [[Pin System]]
| Weight
| [[Body Screw]]
| [[Body Sexbolt]]
| [[Pivot_System#Bushing|Bushing]]
| [[Pins]]
| [[Pivot Screws]]
| [[Pivot Sexbolts]]
| [[Washer]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[Armed_Shark|Armed Shark]]
| [[Armed_Shark_Squid_Industries_Krake_Raken|Krake Raken]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL
| [[Pin System#Glued|Glued Zen]]
|
|
|
| 3.267x4.82x6.985
|
| 6.42x2.06x3.41x5.52x7.622
| 6.36x2.02x4.774x8.43x10.575
| 0.490x4.88x10.01
|-
| [[Armed_Shark_Squid_Industries_Nautilus_V2|Nautilus V2]]
| 5Cr15
| [[Construction#Channel|Channel]]
| 7075 AL + G10/CF
| [[Pin System#Tang Pin|Tang]]
|
|
|
| 2.443x4.8x6.340
|
|
|
| 0.5x?x?
|-
| [[Armed_Shark_Squid_Industries_Tsunami|Tsunami]]
| 5Cr15
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 2.849x4.8x6.987
|
| 6.76x1.90x3.39x5.52x7.323
| 6.66x1.90x4.774x7.56x9.392
| 0.494x4.88x10.01
|-
| rowspan="10" | [[Baliplus]]
| [[Baliplus_Fellowship_Blades_Gaboon|Gaboon]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 3.285x4.77x6.278
|
| 6.402x2.30x3.465x6.0x8.375
| 3.385x2.17x4.770x8.20x10.370
| 0.502x4.80x9.430
|-
| [[Baliplus_Squid_Industries_Krake_Raken_V2.5|Krake Raken V2.5]]
| 9cr18mov
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus_Squid_Industries_Krake_Raken_V3|Krake Raken V3]]
| 420
| [[Construction#Channel|Channel]]
| 7075AL
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.200x4.8x6.275
|
|
|
| 0.5x?x?
|-
| [[Baliplus_Fellowship_Blades_Medusa_V2|Medusa V2]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Press-fit|Press fit Zen]]
|
|
|
| 3.278x4.78x6.275
|
| 7.915x2.5x3.430x4.8x7.270
| 7.904x2.5x4.775x8.0x10.598
| 0.400x4.80x11.614
|-
| [[Baliplus_JK_Orca_v1.5|Orca v1.5]]
| VG10
| [[Construction#Channel|Channel]]
| TI
| [[Pin_System#Pinsless|Pinsless]]
|
|
|
| 3.580x4.8x6.330
|
|
|
| 0.7x?x?
|-
| [[Baliplus_Bladerunners_Systems_Replicant|Replicant]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| 3.200x?x6.275
|
|
|
| 0.4x?x?
|-
| [[Baliplus_MachineWise_Serif|Serif]]
|
| [[Construction#Chanwich|Chanwich]]
| Ti
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| 3.025x?x6.275
|
|
|
|
|-
| [[Baliplus_Henninger_Design_Telesto|Telesto]]
| VG10
| [[Construction#Channel|Channel]]
| Ti
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| 3.325x4.8x7.080
|
|
|
| 0.4x?x?
|-
| [[Baliplus_Bladerunners_Systems_Titanium_Barebones|Titanium Barebones]]
| VG10
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| 3.200x?x7.050
|
|
|
| 0.4x?x?
|-
| [[Baliplus_Squid_Industries_Tsunami|Tsunami]]
| VG10
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
| ?x?x6.275
|
|
|
| 0.5x?x?
|-
| rowspan="2" | [[BaliX]]
| [[BaliX_Henninger_Design_Telesto|Telesto]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
| ?x4.96x7.484x
|
|
|
|
|-
| [[BaliX_Bladerunners_Systems_Titanium_Barebones|Titanium Barebones]]
|
| [[Construction#Channel|Channel]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Blue River]]
| [[Blue_River_Squid_Industries_Tsunami|Tsunami]]
|
| [[Construction#Chanwich|Chanwich]]
| TI
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Blue_River_Krake_Raken|Krake Raken]]
|
| [[Construction#Channel|Channel]]
| 7075 AL
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[TheOne]]
| [[TheOne_JK_|Channeled Alpha Beast]]
|
| [[Construction#Channel|Channel]]
| TI
|
|
|
|
| 3.560x4.45x6.986
|
| 6.425x1.60x2.940x5.45x7.154
| 6.506x1.90x2.961x4.485x8.02x9.830
| 0.495x4.55x8.987
|-
| [[TheOne_Benchmade_40|BM40]]
| Ti
| [[Construction#Channel|Channel]]
|
|
|
|
|
| 2.970x4.00x5.783
|
| 5.46x1.47x2.92x5.00x6.48
| 5.50x1.50x3.980x7.50x9.013
| 0.694x4.15x8.02
|-
| [[TheOne_JK_G10_Orca|G10 Orca]]
| Ti
| [[Construction#Channel|Channel]]
| G10
|
|
|
|
| 3.600x4x5.985
|
|
|
| 0.702x4x10.065 (bronze), 0.502x6x10.625 (steel)
|-
| [[WZM]]
| [[WZM_LDY_Cygnus_V2|Cygnus V2]]
|
| [[Construction#Sandwich|Sandwich]]
| 7075 AL + G10
|
|
|
|
| 3.600x4.5x6.996
|
|
|
| 0.5x?x?
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| colspan="14" | [[Custom Parts Makers]]
|-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[A51projects|A51projects]]
| [[A51projects_Hardware|Hardware]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Aesthetic Design]]
| [[Aesthetic Design|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Aesthetic Design|Setsuna Full Channel Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[ARC Knife]]
| [[ARC_Knife_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[ARC_Knife_Replicant_Spacer|Replicant Spacer]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bloqstoys]]
| [[Bloqstoys_Krake_Raken_Rehandles|Krake Raken Rehandle]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Bxndxgeknives]]
| [[BxndxgeknivesReplicant/Kraken_Rehandles|Replicant/Kraken Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[fingermanipulation]]
| [[fingermanipulation_Replicant_scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="4" | [[Fox Fire Factory]]
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v1|Replicant Full Channel Spacers v1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v2|Replicant Full Channel Spacers v2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v3|Replicant Full Channel Spacers v3]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Fox_Fire_Factory_Replicant_Full_Channel_Spacers_v4|Replicant Full Channel Spacers v4]]
|
|
| TI
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Franken_Forge_Blades|Franken Forge Blades]]
| [[Franken_Forge_Blades_Replicant_Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Franken_Forge_Blades_Replicant_Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hammer Designs]]
| [[Hammer_Designs_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Henninger_Design|Henninger Design]]
| [[Henninger_Design_Replicant_Reblades|Replicant Reblades]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Henninger_Design_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Hourglass_Blades|Hourglass Blades]]
| [[Hourglass_Blades_Krake_Raken_Reblade|Krake Raken Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Hourglass_Blades_Replicant_Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[JTDesigned]]
| [[JTDesignedReplicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Kuski_Craft|Kuski Craft]]
| [[Kuski_Craft_Barrel|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MCK_Balisong|MCK Balisong]]
| [[MCK_Balisong_Replicant_Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[MinecraftChickenGod]]
| [[MinecraftChickenGod_Replicant_Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Palethius]]
| [[Palethius_Replican_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Patient_zero_balisong|Patient zero balisong]]
| [[Patient zero balisong]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Spasmfingers]]
| [[Spasmfingers_Nautilus_Scales|Spasmfingers Nautilus Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Spasmfingers_Replicant_Scales|Spasmfingers Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="5" | [[Squiggle_Scales|Squiggle Scales]]
| [[Squiggle_Scales_Krake_Raken_Rehandles_V1|Krake Raken V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_6X_Rehandles_V1|6X Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_6X_Rehandles_V2|6X Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_Replicant_Rehandles_V1|Replicant Rehandles V1]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Squiggle_Scales_Replicant_Rehandles_V2|Replicant Rehandles V2]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="3" | [[StaticKnives]]
| [[StaticKnives_Replicant_Reblade|Replicant Reblade]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives_Replicant_Rehandles|Replicant Rehandles]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[StaticKnives_Replicant_Scales|Replicant Scales]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| rowspan="7" | [[Freedom_Fabrication|Freedom Fabrication]]
| [[Freedom_Fabrication_Nautilus_Scales|Freedom Fabrication Nautilus Scales]]
|
| [[Construction#Channel|Channel]]
| G10
| [[Pin System#Tang Pin|Tang]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Liners|Freedom Fabrication Replicant Liners]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Rehandles|Freedom Fabrication Replicant Rehandles]]
|
| [[Construction#Sandwich|Sandwich]]
| TI
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Scales|Freedom Fabrication Replicant Scales]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Replicant_Spacers|Freedom Fabrication Replicant Spacers]]
|
| [[Construction#Sandwich|Sandwich]]
| G10
| [[Pin System#Screw_Zen|Screw Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Titanium_Krake_Raken_Rehandles_V1|Freedom Fabrication Titanium Krake Raken Rehandles V1]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| [[Freedom_Fabrication_Titanium_Krake_Raken_Rehandles_V2|Freedom Fabrication Titanium Krake Raken Rehandles V2]]
|
| [[Construction#Sandwich|Sandwich]]
| TI + G10/CF
| [[Pin System#Hidden_Zen|Hidden Zen]]
|
|
|
|
|
|
|
|
|-
| rowspan="2" | [[Zippy_Balisong|Zippy Balisong]]
| [[Zippy_Balisong_Replicant_Inserts|Replicant Inserts]]
|
|
|
|
|
|
|
|
|
|
|
|
|-
| [[Zippy_Balisong_Replicant_Spacers|Replicant Spacers]]
|
|
|
|
|
|
|
|
|
|
|
|
|}